Full Product Manual

QUICK START GUIDE
QUICK START GUIDE
Socket OVERVIEW
1. Turn off power before you twist a light bulb into the Smart Socket. Ensure the socket is connected correctly
and turn on the power. The green LED light will flash slowly when it is ready for network setup.
2. Make sure your iPhone or iPad (iOS 8.1 or later) is connected to a 2.4GHz Wi-Fi network.
Using the router utility software, shutdown 5GHz Wi-Fi networks.
3. Download and open the free Koogeek Home app from the App Store.
4. Log in or sign up for a Koogeek account or simply tap Skip.
5. Tap “+” on the top right corner and follow the on-screen directions to complete network setup.
Note: To add more sockets (or repeat the socket setup process), tap “+” and you will see the accessory list.
Each accessory has an identification code, e.g., Koogeek-XXX-XXXXXX. Make sure the last 6 characters of the
identification code is consistent with the last 6 characters of MAC on the Smart Socket.
6. When prompted, scan the setup code or manually enter the setup code, and then follow
the step to add the device to the Home and Room.
7. You can assign a name to your device and use this name when speaking to Siri. For example,
you can name your device “Lightbulb”, then launch Siri and speak “Turn on the Lightbulb”.
8. Set up customized scenes to control multiple devices with a single command. For example,
if you assign the “I'm going to bed” command to the scene of turning off bedroom light and
turning on the night light. When you speak “I'm going to bed” to Siri, everything will be done.
9. Please visit
www.koogeek.com for troubleshooting.
Button
Power / Wi-Fi Status Indicator (after setting up)
Press once to manually control the switch (Turning socket “On” or “Off”)
Green LED flashes slowly: Smart Socket is waiting for a Wi-Fi network configuration .
Green LED flashes quickly: Smart Socket is disconnected from a Wi-Fi network .
Green LED stays lit: Smart Socket is “On” .
Green LED is off: Smart Socket is “Off”.
Power / Wi-Fi Status Indicator
Button
Use of the Works with Apple HomeKit logo means that an electronic accessory has been
designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance standards. Apple is not responsible for
the operation of this device or its compliance with safety and regulatory standards.
Controlling this HomeKit-enabled accessory automatically and away from home requires an
Apple TV with tvOS 10.1 or later or an iPad with iOS 10.1 or later set up as a home hub.
Operation is Subject to the Following Two Conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme
avec Industrie Canada exempts de licence standard RSS(s). Son
fonctionnement est soumis aux deux conditions suivantes: (1) Cet appareil ne doit pas
provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles
pouvant causer un mauvais fonctionnement de l'appareil.
www.koogeek.com
f
Follow Koogeek
www.facebook.com/koogeek
Restore factory settings: Press and hold the button for about 10 seconds.
.
.
.
.
When the green LED light flashes slowly, it indicates that you have restored
the device to factory settings.
FAQ
Why did I fail to add my Smart Socket to the Koogeek Home app?
1. Make sure your accessory is powered on and nearby.
2. If you have a dual band router, please shutdown 5GHz Wi-Fi networks and
connect your phone to the 2.4GHz Wi-Fi network.
3. Make sure your accessory’s green LED flashes slowly, if not, please press and
hold the reset button for 10 seconds to restore factory settings.
4. Select the accessory shown on screen, then scan the setup code which can be
found on the device, instruction manual or inner packaging.
5. If the app prompts “Couldn’t add Koogeek –Socket-XXXXXX” after you scanning
the setup code:
(1) delete the current “Home” in Home Settings and close the app;
(2) restore the accessory to factory settings;
(3) add the accessory again.
Smart Socket works normally after restoring factory settings, but it occasionally
gets disconnected from networks and can not be recognized.
1. Make sure the number of Wi-Fi connected devices is within the wireless
network capacity of your router. Otherwise, please replace with another router.
2. Reconnect your iOS devices to Wi-Fi and make sure your Wi-Fi signal is strong
enough.
3. Wait until the network is fixed if your router performs poorly in wireless
networks that might result from network congestion.
4. Check the router setting and see if there is any limit to the number of
simultaneous client connections.
5. Restart your HomeKit accessory or restore your HomeKit accessory to factory
settings, and add your HomeKit accessory to the Koogeek Home app.
6. Update the firmware to the latest version.
How to automate and remotely access my HomeKit accessories?
Please visit www.koogeek.com/support/homekit.html
FCC Notice
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Electrical Ratings
100-240V AC, 50 / 60Hz
25W (Max.)
General use
Safety Warnings
Screw directly into a light fixture
For indoor use only
Turn off power before inspection, installation and removal
Keep children away from Smart Socket
DO NOT clean with liquid
DO NOT use in wet or damp areas
DO NOT exceed the recommended electrical ratings
DO NOT use in precision timing applications where inaccurate timing could be dangerous (sunlamps, saunas, etc.)
DO NOT use with devices that should not be operated unattended
DO NOT touch inside the socket
.
.
.
.
.
.
.
.
.
.
E26(USA)/E27(EU)/LED/CFL
Note:
The use of a HomeKit-enabled accessory need the follow permissions:
Settings > iCloud > iCloud Drive > Turn On
Settings > iCloud > Keychain > Turn On
Settings > Privacy > HomeKit > Koogeek Home > Turn On
Legal
1
3
2
4