ICE MAKER User's Manual KCM-450-AH KCM-450-AH-22 KCM-670-AH This ice maker cannot be used in any country with a voltage supply that does not match the voltage requirements for this unit. ● The following items are not supplied with the unit and will need to be purchased separately. Ice bin Cord set. Water supply and drain hoses. ● This ice maker requires a floor drain. ● A water filtration system is highly recommended(available for purchase with the ice maker) Water filter system Part No.
INDEX 3. 2 1. Safety Precautions .................................................................................. 3~7 2. Installation ................................................................................................. 8~18 Installing height control feet on storage bin .......................... 8 Installing the product and storage bin ............................................. 8~9 Specifications for connecting water supply 10 ..................................
1. Safety Precautions Warning Failure to follow these instructions may result in severe personal injury or death. Caution Failure to follow these instructions may result in parts replacement expense and / or service repair expense. IMPORTANT PROHIBITED DO NOT DISASSEMBLE DO NOT TOUCH DISCONNECT POWER PLUG GROUNDED Warning Use a dedicated receptacle for the ice machine. ◆ An electrical fire may be caused by having more than one unit connected to the same outlet as the ice maker.
Warning Do not place or store heavy items or the top of the product. ◆ Damage from excessive weight can cause the unit to overheat or catch fire. Do not install the machine in a humid area or near a water spray zone. ◆ May cause an electric leak, shock or fire. Stop operation immediately if a burning smell or smoke is detected. Disconnect from the power outlet and shut off the water supply. ◆ Operating the product under bad conditions may cause fire or electric shock.
Warning Do not disassemble Do not modify the ice maker or attempt any repairs without an authorized service provider ◆ Tampering with the icemaker in any way may cause significant damage to the machine. Keep the power cord in good condition. Do not bend the power cord at a sharp angle or place heavy items on it; both actions can damage the power cord. ◆ Damaged cords can cause electric shocks and/or fires. ◆ Contact the customer service center if the power cord or plug is damaged.
Warning When not in use for a long time, disconnect the power plug For long term storage, or product shut down, close the water supply valve, disconnected the power plug and remove the ice from the ice bin. When cleaning or servicing, disconnect the power plug, shut off the water supply, and wait for the ice maker to stop. ◆ It may cause electric shock, fire, or injury. Do not use tools to disconnect power plug.Remove the power plug from the receptacle by holding the plug itself.
Caution Keep area around ice maker clean Remove any moisture, oil, or other hazards from the floor near the product. ◆ Slipping on the ice may cause injury. Keep this operation manual with the ice maker If you transfer ownership of this machine, be sure to provide the new owner with this manual. Please note:The warranty does not transfer with change of ownership. ◆ Refer to the user manual for safety guidelines. Do not slide hands or feet under the ice maker.
2. Installation Installing leveling feet on storage bin These instructions show how to place the ice machine onto the storage bin and make sure it is attached firmly as shown below. The manufacturer is not liable for any incident or injury resulting from the product falling during use. < Installing the storage bin > 1. Screw in the 4 leveling feet onto the bottom of the storage bin. 2. Adjust the height of the foot by turning so they are the same height and the product is level.
4. Slide the machine slowly to the rear so that the back and sides are even. 5. Detach both side panels by loosening the bolts. 6. Reassemble the side panels to complete installation of the machine. 7. Use the brackets to anchor the machine to the wall.
Specifications for connecting water supply [ Connecting water and drain piping ] Appropriate piping /hose size Appropriate water temperature Water pressure Ice making water supply 50 ~ 90 ℉ 20 ~ 80 psi 3/8" MPT Ice making water drain - - 3/4" MPT Water temperature that is too high will decrease the amount of ice produced; pressure that is too low will prevent ice from being made at all. Install an auxiliary pressure pump if the water pressure is below 20psi.
Suitable installation conditions and locations ⊙ Locations away from direct heat sources ◆ The machine should be installed where there is no heat source such as a stove or gas range. Ambient temperature must be between 50 ~ 100 ℉ ⊙ Locations with enough clearance from the walls ◆ The minimum distance required is 8 inches from the walls for normal operation. ⊙ Locations with good ventilation ◆ Poor ventilation will lead to poor ice production.
⊙ Be sure to install the product in a clean location. ◆ Ice is edible; thus, the installation site must be clean and hygienic. ⊙ The product must be installed indoors. ◆ The machine must not be installed outside. ◆ The drain hose must slope downwards at least 1/4" per linear foot to enable smooth draining. ⊙ Install in a place inaccessible to children. ◆ Be sure that children do not get injured or play with ice. No access for children ◆ Make sure to observe the following.
After installation ⊙ Protect the water supply hose Do not place heavy objects on the water supply hose. Do not walk on the hose. ⊙ The water pressure, water temperature, and ambient temperature. This ice maker must be used with a water pressure of 20 ~ 80 psi, water supply of 50 ~ 90 ℉, and ambient temperature of 50 ~ 100 ℉. 20 ~ 80 psi 50 ~ 90 ℉ 50 ~ 100 ℉ Connect to a potable water supply only. 1. Plugging into the power supply.
About grounding ※ Be sure to ground the product to prevent electric shock. ⊙ Grounding method - With grounding terminal When plugging the icemaker into a 208-220V outlet (670-AH) that is equipped with a grounding terminal, extra grounding is not necessary. ⊙ Grounding method - Without grounding terminal When plugging the icemaker into an outlet without a grounding terminal, connect the ground wire to the copper plate and then bury it under the ground.
3. Check before use 3-1. Remove shipping tape before operation After removing the front cover, be sure to remove the shipping tape from the sensor and Water distributor Ice thickness sensor Ice thickness adjusting bolt Evaporator water curtain. - Unless the tape is removed, the machine will not work. 3-2.
How to use the drain switch To have transparent ice or to reduce scale in the water trough, turn the switch to the "ON" position. If you keep the drain switch in the “ON” position,the unit will drain the remaining part of the water in the ice machine by flushing with clean water. (about 1 Qt) after every ice cycle. ◆ When the drain switch is in the “ON” position, it will take longer to make ice, reducing the amount of ice made per hour.
When turning off the drain valve 1. Open the front panel by loosening two screws. 2. Turn off the drain switch in the control box; Water draining after each cycle will be stopped. Power switch Drain switch ※ This is applicable if the user wants to increase the amount of ice. (Ice quality may deteriorate slightly.
4.
4.
5. General product information SPECIFICATIONS ITEM Ice Size/Number Size (W X D X H) Power Supply Maximum Manufacturing Capacitor UNIT KCM-670-AH mm 9.5 X 29 X 22 / 360 inch 0.37 X 1.14 X 0.86 / 360 mm inch - 762 X 610 X 580 30 X 24 X 22.8 220V / 60Hz kg/day 10℃ 285 lb/day 50℉ 628 Before being packaged kg 97 lb 213.8 After being packaged kg 99 lb 218.
SPECIFICATIONS ITEM UNIT Ice Size 9.5 X 29 X 22 inch 0.37 X 1.14 X 0.86 762 X 610 X 580 30 X 24 X 22.8 115V / 60Hz kg/day 10℃ 200 lb/day 50℉ 441 Before being packaged kg 64 lb 141 After being packaged kg 77 lb 169.8 Power Supply Weight Cooling Unit mm mm inch - Size (W X D X H) Maximum Manufacturing Capacitor KCM-450-AH Model Compressor No.
SPECIFICATIONS ITEM UNIT Ice Size mm 9.5 X 29 X 22 inch 0.37 X 1.14 X 0.86 mm inch - 560 X 619 X 553 22 X 24.3 X 21.7 115V / 60Hz kg/day 10℃ 200 lb/day 50℉ 441 Before being packaged kg 67.5 lb 148.8 After being packaged kg 78.
6. Cleaning (at least once a month) 1. Turn off the power switch. 2. Detach the drain plug to remove any residue in the water trough. 3. Detach the water curtain and clean with soft cloth. 4. Detach the water distributor and clean thoroughly. 5. Dilute mild detergent (for home use) to clean the product (1 spoonful per quart of water). After cleaning the product with detergent, be sure to rinse the machine for at least 20 minutes; there should be no residue left from the detergent.
Cleaning Refer to cleaning procedure for complete details. Clean the machine every two months. 1. Set the main switch to the OFF position after ice falls from the evaporator or set the switch to the OFF position and allow the ice to melt off the evaporator. CAUTION - Do not use sharp objects to remove the ice from the evaporator. Damage may result. 2. Remove all ice from the bin and water from the water trough. 3. Remove the upper or front panel and shut off the water supply. 4.
SANITIZING PROCEDURE Refer to this detailed sanitizing procedure and clean the machine at least once a month. 1.Set the main switch to the OFF position after ice falls from the evaporator at the end of a harvest cycle. Or, set the main switch to the OFF position and allow ice to melt off the evaporator. ※ CAUTION:Do not use sharp objects to remove the ice from the evaporator. Damage may result. 2. Remove all water and ice from the bin and water trough. 3.
[ WASH function ] 1. Turn off the top right power switch. Turn off the power switch inside the front cover. 2. Remove all ice; discard or store in a proper container such as ice box or freezer. 3. Dilute 1.6oz of mild detergent in 2.1gal of water at 95-113 ℉ and pour into the water trough. 4. Turn the power switch at the back to WASH. The pump motor will run for about 90 seconds, and then stop for about 30 seconds. This cycle will be repeated 5 times. 5. Repeat the cycle above for 2 or 3 times.
7. Troubleshooting Check the following chart if machine is not operating correctly: If the machine continues to operate incorrectly, contact your local dealer or customer service center. Provide them with the following details: Model, serial number, name of local dealer, date of purchase, and current condition of the product. Operating Condition Check Points Measures 1. Is the machine supplied with electric power? 1. Supply it with electric power.
8. Manufacturers Limited Warranty Ice Machine Limited Warranty Subject to the exclusions and limitations below, MVP Group warrants to the original consumer that any new ice machine shall be free of defects in material or workmanship for the warranty period outlined below, under normal use and maintenance, and upon proper installation and start up in accordance with the instruction manual supplied with the product.
Replacement Part Warranty: Following the expiration of MVP Group’s product warranty, any replacement part purchased by the equipment owner is warranted for a period of ninety (90) days from installation date of replacement part, the compressor or evaporator is warranted for a period of one (1) year from installation date of replacement part. All parts are to be sourced through the local Distributor to qualify for warranty.
MEMO 30
MEMO 31
MEMO 32
Toll Free: (888) 275-4538 international: (514) 737-9701 Fax: (514) 342-3854 Toll Free Fax: (877) 453-8832 3240416-00