® Superior Liquid Cooling Systems PSU-1300ATX-12N User’s Manual English v1.1 Protected by U.S. Patents 6,313,990; 6,664,627; 7,167,366; 7,295,436 Other Technology Pending U.S.
Koolance PSU-1300ATX-12N Power Supply (Addendum 1.0) The user manual may have been updated since this copy was printed. Please check the Koolance website at www.koolance.com/ support for the latest product manuals. Your Koolance PSU-1300ATX-12N power supply may arrive with rubber inserts to protect the top nozzle connections during shipping. These should be removed before inserting your desired nozzles.
This User Manual is updated regularly. Please be sure to check our support page for a newer version of this guide: www.koolance.com/support GENERAL PRECAUTION Please read this manual carefully before beginning the installation of your Koolance system. This manual assumes the user has basic experience in building and configuring computer systems. Information referring to traditional hardware assembly is intentionally brief.
WARNING: Due to U.S. regulation, power draw over a typical household 110-volt AC line limits the PSU-1300ATX-12N to 1300W output. When powered by a 220V AC circuit, the unit is capable of outputting 1700W. Users are responsible for safely supplying adequate AC power for the PSU-1300ATX-12N power supply. Always observe local fire and electrical regulations. WARNING: Never open the power supply, expose the internal liquid coolant, or remove the internal liquid coolant.
Internal Connections The modular connections must match their appropriate plug on the PSU (power supply unit). Pay careful attention to the direction of each plug and notch while inserting, as some are upside-down. Never force a plug into the PSU. 12V 8-pin (Motherboard) Motherboard Main ATX SATA, IDE, Peripherals PCI-Express *Internal Temp. Sensor PCI-Express 4 x 8-pin, 4 x 6-pin Peripheral x 2 Cables (IDE, Floppy, etc.
External Connections DC Signal Light Main AC Power In Main Power Switch (Not used) 12V Fan Out External Nozzle Socket (In/Out) External Nozzle Socket (In/Out) Plugs for Internal Coolant (DO NOT OPEN!!!) ! CAUTION: The bottom (internal) coolant socket plugs must remain closed at all times. Otherwise, the sealed internal fluid will leak. This liquid is not inexpensive and evaporates very quickly. Tampering or opening the bottom (internal) coolant plugs will void the product warranty.
! CAUTION: The PSU-1300ATX-12N power supply is not a selfdissipating product and must be connected to an existing liquid cooling system (not included). The power supply will overheat and may become permanently damaged if operated without proper cooling. Preparation for Installation ! CAUTION: The PSU-1300ATX-12N must be mounted in an upright direction. Other orientations will not allow the pump to circulate coolant properly, or coolant will not fully submerge internal heat sources.
For most computer cases, the PSU-1300ATX-12N must be installed from inside the chassis due to its width. If you do not have a Koolance case, please skip to the next section. Koolance PC3-726, PC3-736, PC4-1026, and PC4-1036 systems must give up one hard drive cage in order to fit the PSU-1300ATX-12N. Begin by removing the screws for this rear drive cage, the top screws for the front hard drive cage, and the PSU partition wall. Screws are located above and below the hard drive area.
Support Bracket Bracket Wing The PSU-1300ATX-12N is supplied with an optional support bracket. For chassis with top-mounted power supplies (above the motherboard), the support bracket can help increase case stability. The bracket is screwed into the PSU’s cable panel, on the same side of the computer less frequently opened. It is adjustable to meet the computer’s side panel. Velcro strips are provided to be applied in between the bracket’s flat wing and the computer chassis side panel.
Tubing Connection Once the power supply is mounted inside the chassis, insert and tighten the desired inlet and outlet nozzles (purchased separately). These should only be installed on the top nozzle sockets! Attach the inlet and outlet tubing to the inlet and outlet nozzles. If you require the PSU-1300ATX-12N hoses to be connected inside the computer chassis, install the supplied L-bracket into an available rear card slot.
Specifications AC Input Operating Range: 90-264VAC@110V, 180-264V@220V, Auto-switching Frequency: 47-63Hz Current: 15A @ 110V, 10A @ 230VAC PFC: Active Efficiency: 83 (avg) - 85% (max) @ 110V; 86 (avg) - 87% (max) @220V DC Output Output Max: +5V @ 30A +3.3V @ 30A +12V @ 120A (12V1@20A, 12V2@20A, 12V3@40A, 12V4@40A) 12V1, 12V4, 3.3V total combined power = 650W@110V, 850W@220V 12V2, 12V3, 5V total combined power = 650W@110V, 850W@220V -12V @ 0.8A +5VSB @ 3.
Limited Warranty Koolance Incorporated (“Koolance”) warrants each new PSU-1300ATX-12N liquidcooled power supply (“the system”), against defects in materials or workmanship for a period of three years from the date of purchase, and agrees to repair or replace any defective Koolance system without charge. Shipping costs are nonrefundable. This warranty is non-transferable. All warranty claims must be accompanied by the original proof of purchase.
www.koolance.
