Commercial Undercounter Ice Maker User Manual for Installation and Maintenance Model: CIM-350
Table of Contents Important Information 3 Warning and safety instruction 4 General 5 Installation 5 Location for Installation 5 Schematic Diagram of Installation 5 Installation Steps 6 Startup and Operation 6 Operation Instruction 7 Instruction of Control Panel 8 Maintenance 9 Service Call 10 Common Faults and Troubleshooting 10 Warranty 11 Note: please keep this manual in a place accessible to users at any time..
Important Information Please pay attention to the following warning labels on the ice maker The label indicates a flammable foaming agent “Cyclopentane” used. There is a risk of fire. The label indicates a flammable refrigerant “R290” used. There is a risk of fire. The label indicates a hazardous voltage. There is a risk of electric shock. The label indicates a hazardous voltage. There is a risk of electric shock. The label indicates rotating components inside.
Instruction of symbols in this Manual Warning sign, special attention is required. Warning sign, special attention is required, and operation is prohibited.
Warning and safety instruction This product cannot be used in outdoor environment. This ice machine is not intended for use by children, and those with physical weakness, slow response, or mental disorders. ✦ The installation, repair or maintenance of this ice machine must be carried out by professional and qualified personnel, or electric shock, fire, personal injury may cause from incorrect operation.
EXPLOSION. DISPOSE OF PROPERLY IN ACCORDANCE WITH FEDERAL OR LOCAL REGULATIONS. FLAMMABLE REFRIGERANT USED. SERVICE PERSONNEL. DO NOT PUNCTURE REFRIGERANT TUBING. • • CAUTION – RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. CONSULT REPAIR MANUAL/OWNER'S GUIDE BEFORE ATTEMPTING TO SERVICE THIS PRODUCT. ALL SAFETY PRECAUTIONS MUST BE FOLLOWED. CAUTION – RISK OF FIRE • CAUTION – RISK OF FIRE OR EXPLOSION DUE TO PUNCTURE OF REFRIGERANT TUBING; FOLLOW HANDLING INSTRUCTIONS CAREFULLY.
Modular Ice Maker User Manual for Installation and Maintenance Schematic Diagram of Installation
Modular Ice Maker User Manual for Installation and Maintenance Installation Steps 1. Check if the ice machine is in good condition and the accessories are complete; check the machine model and the machine nameplate. 2. Clean the ice bin and the food area inside with a sponge soaked in warm water and soap. Then wash and dry it with potable water. body. Note: This machine is equipped with an inlet water filter. The filter will keep impurities from the water used as the machine is running.
automatically. machine; 3. For normal operation, please confirm: ✔ The ice machine has no abnormal noise; ✔ There is water in the water trough and no overflow occurs; ✔ The ice machine has no abnormal vibration; ✔ The pump is working properly and water is flowing evenly on the evaporator; ✔ It takes about 10 to 20 minutes to make one batch ice, depending on the ambient temperature and the temperature of the water.
Modular Ice Maker User Manual for Installation and Maintenance Instruction of Control Panel 1. LED Display: • Self-check： Display “ini” code. • Preparing： Counting seconds upward • Ice making: Counting seconds upward as the water temperature decreases to 32 degrees F. Counting seconds downward to 0 s after. • Ice Harvest: Counting seconds upward. • Clean: Display “CLE” during cleaning and descaling; Display “STL” during sterilizing; Display “rin” during rinsing. 2.
The fault code and its comments are displayed as follows: Code Error Machine status E01 Water Curtain failure or Ice Full Switch Sleeping mode will recover after the water curtain is reset E03 Ice Harvest Overtime Protective shutdown E04 High Temperature Protective shutdown E05 Water Shortage Fault E06 High Pressure E07 Contestation Sensor Open Circuit Error light comes on every 5 seconds E08 Condensation Sensor Short Circuit Error light comes on every 5 seconds E13 Water Level Contr
Water pipe In order to ensure food safety, the water pipe of the ice machine should be cleaned regularly. Wintering Turn off the water and power supply, drain the residual water from the water trough, inlet pipe and drain pipe. Note: Be careful when doing the condenser cleaning as the edges of the fins are sharp. The maintenance of the ice machine is not covered by the manufacturer's warranty! Clean ounction Note: Please empty the bin of ice in advance.
✔ Check the nameplate located on the side or back of the ice machine and record the model and series number of the ice machine.
Troubleshooting Issue Potential cause Troubleshooting Not working Power switch not turned on Turn on the power switch Indicator is “OFF” Plug is loose Check plug and socket The display shows E04 high temperature The ambient temperature is too high Normal working temperature 41-95°F Condenser or air filter is dirty and Clean the condenser and air filter.
Modular Ice Maker User Manual for Installation and Maintenance If you are experiencing any issue with your unit, please contact us right away. Phone 7 1 8 -576-6342 Email support@koolmore.
This warranty is only valid on equipment purchased from an authorized dealer. Locate the model number on the rating label Next, call 1-718-576-6342. You must have the model number when contacting service technicians.
