Test Report No.
Wide LCD Monitor User's Guide Models KL1724BM LPP
INTRODUCTION FCC Compliance Statement .......................................................................................................... i Safety Instructions ................................................................................................................................... iii General Information ............................................................................................................................... 1 Equipment Check list ......................................
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.
INTRODUCTION SAFETY INSTRUCTIONS DOC COMPLIANCE NOTICE: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. O Handling INTRODUCTION FCC COMPLIANCE STATEMENT Due to its fragile glass panel, this monitor must be handled with caution and not be exposed to impact or shock.
INTRODUCTION GENERAL INFORMATION O Caution Your new LCD monitor incorporates the latest state-of the art color Liquid Crystal Display (LCD) technology providing a wider viewing angle with higher contrast ratio. 1. Do not open any covers on the monitor. No user serviceable parts are inside. 2. In an emergency, disconnect the AC power plug. 3. To avoid electrical shock, disconnect the power cord from the monitor before connecting the signal cable to the computer. 4. Keep away from liquids and flame.
INTRODUCTION MONITOR FEATURES Before operating your display, please check to make sure that all of the items listed are present in your package: * Supports Analog and Digital(DVI-D) IBM compatible PC, Apple MacintoshTM(Adapter optional) INTRODUCTION EQUIPMENT CHECK LIST * Supports DPMS for monitor power management Accessory Box * Support DDC2B * On Screen Control : Auto-Tune, Contrast, Brightness, H/V Position, H-Size, Phase, Auto-Level, Color Control, Input Select, Volume, Mute, OSD,Position OSD
INSTALLATION 1. Before you connect the the cables, make sure the monitor and system unit power switches turn off. 2. Plug the 15-pin signal cable or 24-pin DVI cable between the rear of your Monitor and system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3. Plug the Audio Cable between Audio input Jack in the rear of your monitor and audio output of your system. OSD Buttons : The OSD control keys are located on lower left of the monitor.
CONTROL BUTTONS ON-SCREEN DISPLAY GETTING STARTED Before activating the OSD menu, the button can be used to automatically adjust the display to the proper size and horizontal and vertical position and color. 4 3 2 1 Button Description : 1. 2. 3. 4. 6 : Exits the On Screen Control. Do Auto Tune function. : Move selected icon up to select one of the controls. Increase the control value. : Move selected icon down to select one of the controls. Decrease the control value.
MENU DESCRIPTIONS MENU DESCRIPTIONS PHASE Select this control menu, and then use the and buttons to adjust the screen image until it looks focused, crisp and sharp. AUTO-LEVEL COLOR CONTROL Select this control menu, then use the and buttons to scroll to the desired color temperature. Use the button to select the 9300K, 6500K, 5500K, or USER for custom setting.
MENU DESCRIPTIONS POWER MANAGEMENT AUDIO LED INDICATOR (POWER MANAGEMENT ACTIVE) VOLUME Select this control menu, and then use the and buttons to increase or decrease audio sound level. This function can be used by hot key( ) on the front of monitor. and buttons to select TEXT/ MOVIE Power Mode H-Sync V-Sync Video LED Color Select this control menu, and then use the and buttons to select proper image either text mode or movie mode. Default setting is Text mode.
TIMING GUIDE PIN ASSIGNMENT The LCD is a multi-frequency display. It operates at horizontal frequencies between 30KHz ~ 80KHz and vertical frequencies between 55Hz ~ 75Hz. Because of its microprocessor-based design, it offers autosynchronization and auto-sizing capabilities. This monitor offers 10 preprogrammed settings that are listed in the following timing table.
SPECIFICATIONS TROUBLESHOOTING Color Filter Colors Glass surface 17 diagonal viewable screen TFT (Thin Film Transistor), Active Matrix Panel, 0.2895 x 0.2895mm pixel pitch R,G,B vertical stripe 16.7M Anti-glare coating Left / Right Up / Down 70 ° / 70 ° 70 ° / 70 ° Contrast Ratio Typ. 450:1 Luminance of White Typ. 400cd/m Compatibility PC IBM XT, AT, 386, Pentium or PS/2 and compatibles(from VGA and DVI up to 1280 x 768 @ 75Hz NI.
TROUBLESHOOTING MEMO Connect the LCD Monitor to another computer. Check the graphics card for proper sync scheme (or sync polarities) to match the LCD Monitor’s specifications. Double (split) screen image. Make sure your graphics card is set to Non-Interlaced mode. Entire screen image rolls (scrolls) vertically. Make sure the input signals are within the LCD monitor’s specified frequency range. (Maximum: VESA, MAC 1280 x 768@75Hz) REFERENCE Connect the video cable securely.
MEMO 18
