Test Report No.
LCD Monitor User’s Guide Models KL1920BM
TABLE OF CONTENTS INTRODUCTION FCC Compliance Statement ………………………………… Safety Instructions ……………………………………………. General Information ………………………………………….. Equipment Check list ………………………………………… Monitor Features ……………………………………………… ⅰ ⅲ 1 2 3 GETTING STARTED Installation ……………………………………………………… 4 Control Buttons ……………………………………………….. 6 On-Screen Display …………………………………………… 7 ON-SCREEN CONTROLS Menu Descriptions …………………………………………… 8 REFERENCE Power Management …………………………………………. Timing Guide ………………………………………………….
INTRODUCTION FCC COMPLIANCE STATEMENT Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of FCC Rules. These llimits Are designed to provide reasonable protection against radio frequency Interference in a residential installation. This equipment generates, uses And can radiate radio frequency energy. If not installed and used in Accordance with the instructions, it may cause interference to radio Communications.
■ Handling Due to its fragile glass panel, this monitor must be handled with Caution and not be exposed to impact or shock. Never touch the display area or rub it with a hard object or tool, as the Panel is easily scratched. INTRODUCTION SAFETY INSTRUCTIONS ■ Cleaning The display area is sensitive to scratching. Do not use ketone-type Cleaners(i.e.acetone),ethyl alcohol, toluene, ethyl acid or methyl Chloride to clean the panel. Doing so may result in permanent damage.
■ Caution 1. Do not open any covers on the monitor. No user serviceable parts are inside. INTRODUCTION SAFETY INSTRUCTIONS 2. In an emergency, disconnect the AC power plug. 3. To avoid electrical shock, disconnect the power cord from the monitor before connecting the signal cable to the computer. 4. Keep away from liquids and flame. Do not immerse this monitor in water or any other liquid. Do not use this device in excessively hot conditions. 5. Handle the power cord with care.
Your new LCD monitor incorporates the latest state-of the art color Liquid Crystal Display(LCD) technology providing a wider viewing angle with Higher contrast ratio. INTRODUCTION GENERAL INFORMATION Your new LCD monitor has many advantages : safe from electromagnetic Wave, llights, sharps and slims. This makes the monitor extremely Suitable in the environment of administration, transportation system Research, etc. Your new LCD monitor is designed for Analog, Digital inputs.
Before operating your display, please check to make sure that all of the Items listed are present in your package : INTRODUCTION EQUIPMENT CHECK LIST ◆ Power Requirements The monitor is equipped with an auto-sensing power supply for voltage Ranging from 100-120VAC/200-240VAC, 50/60Hz. Confirm the power rating of the AC Source before you plug the AC Cable to the wall outlet.
• · · · · · · · · • • • · • Supports Analog IBM compatible PC, Apple MacintoshTM(Adapter optional) Supports DPMS for monitor power management Support DDC2B On Screen Control : Auto-Tuning, Contrast, Brightness, H/V Position, H-Size, Phase, Auto-Level, Color Control, Sharpness, TEXT/MOVIE, OSD Position, OSD Time-out, Power Save Delay, Language, Information. Built-in color active matrix TFT(Thin Film Transistor) Liquid Crystal Display(LCD) that uses amorphous silicon TFTs as a switching device.
◆ Follow these steps to install the monitor 1. Before you connect the cables, make sure the monitor and system unit power switches turn off. GETTING STARTED INSTALLATION 2. Plug the 15-pin D-SUB, 24-pin DVI signal cable between the rear of your Monitor and system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3. Plug the Audio Cable between Audio input Jack in the rear of your monitor and audio output of your system. 4.
OSD Buttons : The OSD control keys are located on lower left of the Monitor. (Enter) a. No OSD : This buttons will enable the main OSD menu. b. Main OSD menu : Press this button to enter to the selected OSD control menu. c. Control OSD menu : Swap the control item. GETTING STARTED CONTROL BUTTONS ▲ or ▼(Up/Down) : Use these buttons to increase or decrease each value. a. No OSD : - ▲ : Contrast & Brightness control menu will be shown.
GETTING STARTED CONTROL BUTTONS Button Description : 1. 2. 3. 4. 5. :Display On Screen Control menu. Access the control menu. ▲:Move selected icon up to select one of the controls. Increase the control value. ▼:Move selected icon down to select one of the controls. Decrease the control value. A:Exit the On Screen Control. Do Auto Tune function. I :Select the Display mode. Switch Text mode to Movie mode(Press this button for 2 seconds.) Switch D-SUB(Analog) to DVI(Digital)(Press this button prompt.
This LCD monitor features an On-Screen Display(OSD)menu. These Icons are designed to make your monitor display settings easier. When Highlighted, the icons illustrate the control function to assist you in Identifying which control needs adjustment. GETTING STARTED ON-SCREEN DISPLAY Before activating the OSD menu, the ‘A’ button can be used to Automatically adjust the display to the proper size and horizontal and Vertical position.
ON-SCREEN CONTROLS MENU DESCRIPTIONS AUTO-TUNING This control will automatically make adjustments to the horizontal and vertical size, horizontal and vertical position,phase and color. CONTRAST This control allows you to make adjustments to the contrast of the display screen. BRIGHTNESS Selecting this control menu allows you to make adjustments to the luminosity level of the display screen.
Phase Select this control menu, and then use the ▲ and ▼ buttons to adjust the screen image until it looks focused, crisp and sharp. AUTO-LEVEL This control will automatically make adjustment to the input levels of video signal. COLOR CONTROL Select this control menu, then use the ▲ and ▼ buttons to scroll to the desired color temperature. Use the button to select the 9300K, 6500K, 5500K, or USER for custom setting.
INPUT SELECT Select this control menu, and then use the ▲ and ▼ buttons to select proper video input signal either D-SUB(Analog R,G,B)or DVI(TMDS). Default setting is D-SUB. This function can be used by hot key on the front of monitor TEXT/MOVIE Select this control menu, and then use the ▲ and ▼ buttons to select proper image either text mode or movie mode. Default setting is Text mode. This function can be used by hot key on the front of monitor.
LED INDICATOR (POWER MANAGEMENT ACTIVE) The power management feature is comprised of two stages : On or Out Of Range(Blue), Off(Blue blinking). In the off mode, all circuitry in the monitor is shut down, except for a low power detection circuit.
The LCD is a multi-frequency display. It operates at horizontal frequencies between 30KHz-80KHz and vertical frequencies between 55Hz-75Hz. Because of its microprocessor-based design, it offers autosynchronization and auto-sizing capabilities. This monitor offers 10preprogrammed settings that are listed in the following time table. REFERENCE TIMING GUIDE These preset modes cover most of the common video modes supported by popular graphics adapters.
REFERENCE PIN ASSIGNMENT Note:When resolutions are shown that are lower than the pixel count of the LCD panel, text may appear choppy or bold. This is normal for all current flat panel technologies when displaying non-native resolutions on a full screen(below than 1280×1024 resolution). In flat panel technologies, each dot on the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be down.
LCD Type Color Filter Colors Glass surface 19”diagonal viewable screen TFT(Thin Film Transistor), Active Matrix Panel, 0.294×0.294mm pixel pitch R,G,B vertical stripe 16.7M Viewing Angles Left/Right Up/Down 85o / 85o 85o / 85o Contrast Ratio Typ. 500:1 Luminance of White Typ. 250cd/m2 Compatibility PC IBM XT,AT,386,486,Pentium or PS/2 and compatibles(from VGA and DVI Up to 1280×1024@75Hz) Refresh Rate Max.
◆ No power • Flip the power switch ON. The Power LED turns on. • Make sure AC power cord is securely connected to a power outlet. REFERENCE TROUBLESHOOTING ◆ Power on but no screen image. • Make sure the video cable attached with this monitor is tightly secured to the video output port on the back of the computer. • Adjust the brightness and contrast. ◆ Image is unstable, unfocused. • Use “AUTO-TUNE” to adjust automatically.
• Connect the LCD Monitor to another computer. • Check the graphics card for proper sync scheme(or sync polarities) to match the LCD Monitor’s specifications INTRODUCTION TROUBLESHOOTING ◆ Double (split) screen image. • Make sure your graphics card is set to Non-Interlaced mode. ◆ Entire screen image rolls (scrolls) vertically. • Make sure the input signals are within the LCD monitor’s specified frequency range. (Maximum:VESA, MAC1280×102475Hz) • Connect the video cable securely.
