User Manual

284
Effects
Dynamics (Dynamic)
Dynamics (Dynamic)
0: No Effect
Select this option when you do not use any effects.
1: Stereo Compressor
This effect compresses the input signal to regulate the level and
give a “punchy” effect. It is useful for guitar, piano, and drum
sounds. This is a stereo compressor. You can link left and right
channels, or use each channel separately.
a: Envelope Select
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
b: Sensitivity
g: Output Level
The “Sensitivity” parameter sets the sensitivity of the compres-
sor. If this parameter is set to a higher value, lower level sounds
will be boosted. With a higher Sensitivity, the overall volume
level is higher. To adjust the final volume level, use the “Output
Level” parameter.
c: Attack
This parameter controls the attack level.
2: Stereo Limiter
The Limiter regulates the input signal level. It is similar to the
Compressor, except that the Limiter compresses only signals that
exceed the specified level to lower unnecessary peak signals. The
Limiter applies a peaking-type EQ to the trigger signal (which
controls the degree of the Limiter effect), allowing you to set any
band width to be covered. This effect is a stereo limiter. You can
link left and right channels, or use each channel individually.
a
Envelope
Select
L/R Mix,
L/R Individ-
ually
Determines whether the left and
right channels are linked or used
separately
b Sensitivity 1...100 Sets the sensitivity
c Attack 1...100 Sets the attack level
d EQ Trim 0...100 Sets the EQ input level
e
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency (high
or mid-high) of the high-range
equalizer
f
Pre LEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the High EQ
g
Output Level 0...100
Sets the output level of the
compressor
Src Off...Tempo
Selects the modulation source for
the compressor output level
Amt –100...+100
Sets the modulation amount for the
compressor output level
h
Wet/Dry
Dry, 1:99...99:1,
Wet
Sets the Balance between the wet
and dry signal
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
FX Amt
FX Amt
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ HEQ
LEQ
HEQ
Compressor
Compressor
Envelope Select
Output Level
Output Level
Envelope - Control
Envelope - Control
a
Envelope
Select
L/R Mix,
L Only, R Only,
L/R Individ-
ually
Selects from linking both channels,
controlling only from left channel,
only from the right channel, or
controlling each channel individ-
ually
bRatio
1.0 : 1…
50.0 : 1,
Inf : 1
Sets the signal compression ratio
c Threshold [dB] –40...0
Sets the level above which the
compressor is applied
v
Attack 1...100 Sets the attack time
Release 1...100 Sets the release time
e
Gain Adjust
[dB]
–Inf,
–38...+24
Sets the output gain
Src Off...Tempo
Selects the modulation source for
the output gain
Amt –63...+63
Sets the modulation amount of the
output gain
f
Side PEQ Insert Off, On
Toggles between on/off of the
trigger signal’s EQ
Trigger
Monitor
Off, On
Switches between effect output
monitor and trigger signal monitor
g
Side PEQ
Cutoff [Hz]
20...12.00k
Sets the EQ center frequency for the
trigger signal
Q 0.5...10.0
Sets the EQ bandwidth for the
trigger signal
Gain [dB] –18.0...+18.0
Sets the EQ gain for the trigger
signal
h
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Sensitivity=100
Sensitivity=40
Dry
Wet
Time
Level
Compressor - Sensitivity
Louder
Dry
Wet
Time
Level
Attack=80
Attack=20
Compressor - Attack
Left
Right
FX Control BUS 1
FX Control BUS 2
FX Amt
FX Amt
Stereo In - Stereo Out
Limiter
Limiter
Envelope Source
Gain Adjust
Gain Adjust
Side PEQ
Envelope - Control
Envelope - Control
Trigger Monitor
+
Envelope Select
Pa300 User Manual v150 (English).book Page 284 Saturday, March 29, 2014 5:29 PM