User Manual

286
Effects
Dynamics (Dynamic)
4: St.MasteringLimtr
(Stereo Mastering Limiter)
This is a stereo limiter that is optimized for mastering songs.
5: Stereo Gate
This effect mutes the input signal when it falls below a specified
level. You can also invert the on/off status of the gate, or use
note-on/off messages to turn the gate on/off directly.
c: Threshold
d: Attack
d: Release
“Threshold” specifies the level at which gating occurs when
“Envelope Select” is set to L/R Mix, L Only, or R Only.
“Attack” and “Release” specify the attack time and release time of
the gate.
c: Polarity
This inverts the polarity of the gate on/off operation. With the
“–” setting, the gate will close when the input signal exceeds the
specified level. The direction in which the modulation source
opens or closes the gate will also be reversed.
e: Delay Time [msec]
This sets the delay time for the input to the gate. When using
shorter Attack Time settings, you can lengthen the Delay Time
so that the sound is input after the gate opens.
a Threshold [dB] –30.0...0.0
Sets the level above which the
compressor is applied
b
Out Ceiling
[dB]
–30.0...0.0 Sets the output gain
c Release [msec] 0.50...1000.0 Sets the release time
d
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
a
Envelope
Source
D-mod, Input
Selects the source to control the
gate: D-mod control, or use the
input signal as a trigger
b
Envelope
Select
L/R Mix,
L Only,
R Only
Selects the control signal: left and
right linked, left only, or right only
Src Off...Tempo
Selects the source that will control
the gate when Envelope Src = D-
mod
c
Threshold 0...100
Sets the level at which gating is
applied
Polarity +, – Switches the polarity of gating
d
Attack 1...100 Sets the attack time
Release 1...100 Sets the release time
e
Delay Time
[msec]
0...100
Sets the delay time for the gate
input
f
Side PEQ Insert Off, On
Switches the trigger signal equalizer
on/off
Trigger
Monitor
Off, On
Switches between monitoring the
effect output and the trigger signal
g
Side PEQ
Cutoff [Hz]
20...12.00k
Sets the center frequency of the
equalizer for the trigger signal
Q 0.5...10.0
Sets the bandwidth of the equalizer
for the trigger signal
Gain [dB] –18.0...+18.0
Sets the gain of the equalizer for the
trigger signal
h
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
Stereo In - Stereo Out
Limiter
Limiter
Out Ceiling
Out Ceiling
Envelope - Control
+
Left
Right
FX Control BUS 1
FX Control BUS 2
FX Amt
FX Amt
Stereo In - Stereo Out
Envelope Source
Gain Adjust
Gain Adjust
Side PEQ
Envelope - Control
Envelope - Control
Trigger Monitor
+
Envelope Select
Gate
Delay
Gate
Delay
D
-mod
Input Level
Output Level
Threshold
Louder
Louder
Threshold
Attack=1
Release=1
Attack=100
Release=100
Dry
Wet
Wet
Attack
Release
Gate - Attack / Release
Gate - Threshold
Pa300 User Manual v150 (English).book Page 286 Saturday, March 29, 2014 5:29 PM