User Manual

290
Effects
EQ and Filters (EQ/Filter)
11: St. Vintage Wah
(Stereo Vintage/Custom Wah)
This effect simulates the tonal character of a vintage wah pedal.
You can customize the tone and range settings.
a: Shape
This parameter specifies the sweep curve of the wah. It applies to
all control via auto-wah, modulation source, and LFO, and lets
you adjust subtle nuances of the wah effect.
a: Mode
b: Frequency Bottom
b: Frequency Top
c: Resonance Bottom
c: Resonance Top
If Mode=Preset, this simulates a vintage wah pedal. In this case,
internally fixed values are used for Frequency Bottom/Top and
Resonance Bottom/Top, and these settings will be ignored. The
settings for Frequency Bottom/Top and Resonance Bottom/Top
are valid if Mode=Custom.
12: St. Random Filter
(Stereo Random Filter)
This stereo band pass filter uses a step-shape waveform and ran-
dom LFO for modulation. You can create a special effect from
filter oscillation.
a
Mode Preset, Custom
Selects either preset or custom
settings
Shape –100...+100 Sets the curve of the sweep
Invert Off, On Inverts the polarity of the sweep
b
Frequency
Bottom
0...100
Sets the lower limit of the wah
center frequency when Mode =
Custom
Frequency Top 0...100
Sets the upper limit of the wah
center frequency when Mode =
Custom
c
Resonance
Bottom
0...100
Sets the lower limit of resonance
amount when Mode=Custom
Resonance Top 0...100
Sets the upper limit of resonance
amount when Mode=Custom
d
Sweep Mode
Auto,
D-mod,
LFO
Selects the control from auto-wah,
modulation source, and LFO
Src Off...Tempo
Selects the modulation source for
the wah when Sweep Mode=D-mod
Manual 0...100
Sets the center frequency when
Sweep Mode=D-mod and
Source=Off
e
Envelope Sens 0...100 Sets the auto-wah sensitivity
Response 0...100
Sets the speed of response when
Sweep Mode=Auto or D-mod
f
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
g
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
h
Output Level 0...100
Sets the output level of the effect
sound
Src Off...Tempo
Selects the modulation source that
will control the effect output level
Amt –100...+100
Sets the modulation amount of the
effect output level
i
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Mode
Preset Setting
Custom Parameters
Stereo In - Stereo Out
D
-mod
Envelope Sens
Shape / Invert
Response
FX Amt
Wah
Sweep Mode
D-mod
Auto
Left
Right
FX Amt
LFO
LFO
Wah
+
a
LFO Waveform
Step-Tri,
Random
Selects the LFO Waveform
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
b
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects the modulation source used
for both LFO speed and step speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
c
LFO Step Freq
[Hz]
0.05...50.00
Sets the LFO step speed (speed that
changes in steps
Amt
–50.00...
+50.00
Sets the modulation amount of LFO
step speed
d
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
e
Step Base Note r...w
Selects the type of notes to specify
the LFO step speed
Times x1...x32
Sets the number of notes to specify
the LFO step speed
f
Manual 0...100 Sets the filter center frequency
Src Off...Tempo
Selects the modulation source for
the filter center frequency
Amt –100...+100
Sets the modulation amount for the
filter center frequency
g
Depth 0...100
Sets the modulation depth of filter
center frequency
Src Off...Tempo
Selects the modulation source of
filter modulation
Amt –100...+100
Sets the modulation amount of filter
modulation
h Resonance 0...100 Sets the resonance amount
i
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Filter
Left
Right
FX Amt
FX Amt
Stereo In - Stereo Out
Filter
LFO Phase
LFO: Step-Tri/Random
Pa300 User Manual v150 (English).book Page 290 Saturday, March 29, 2014 5:29 PM