User Manual

301
Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
Appendix
30: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO phase.
You can create a complex stereo image by setting each block’s
delay time, depth, output level, and pan individually. You can
also fix some of the chorus blocks to combine the chorus and
delay effects.
31: Ensemble
This Ensemble effect has three chorus blocks that use LFO to
create subtle shimmering, and gives three dimensional depth
and spread to the sound, because the signal is output from the
left, right, and center.
c: Shimmer
This parameter sets the amount of shimmering of the LFO wave-
form. Increasing this value adds more shimmering, making the
chorus effect more complex and richer.
a
LFO Frequency
[Hz]
0.02...13.00 Sets the speed of the LFO
b
Tap1 (000)
[msec]
0...1000
Sets the Tap1 (LFO phase=0
degrees) delay time
Depth 0...30 Sets the Tap1 chorus depth
Level 0...30 Sets the Tap1 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap1 stereo image
c
Tap2 (180)
[msec]
0...1000
Sets the Tap2 (LFO phase=180
degrees) delay time
Depth 0...30 Sets the Tap2 chorus depth
Level 0...30 Sets the Tap2 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap2 stereo image
d
Tap3 (090)
[msec]
0...1000
Sets the Tap3 (LFO phase=90
degrees) delay time
Depth 0...30 Sets the Tap3 chorus depth
Level 0...30 Sets the Tap3 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap3 stereo image
e
Tap4 (270)
[msec]
0...1000
Sets the Tap4 (LFO phase=270
degrees) delay time
Depth 0...30 Sets the Tap4 chorus depth
Level 0...30 Sets the Tap4 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap4 stereo image
f
Tap1 Feedback –100...+100 Sets the Tap1 feedback amount
Src Off...Tempo
Selects the modulation source of
Tap1 feedback amount and effect
balance
Amt –100...+100
Sets the Tap1 feedback amount and
modulation amount
g
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
Feedback
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
+
Level
Level
Level
Level
Pan
Pan
Pan
Pan
LFO: Triangle
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
0 [degree]
180 [degree]
90 [degree]
270 [degree]
a
Speed 1...100 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt –100...+100
Sets the modulation amount of LFO
speed
b
Depth 0...100 Sets the depth of LFO modulation
Src Off...Tempo
Selects the modulation source of
the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the
LFO modulation depth
c Shimmer 0...100
Sets the amount of shimmering of
the LFO waveform
d
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
LFO
Shimmer
+
Ensemble
Time
Level
Ensemble LFO
Shimmer
Pa300 User Manual v150 (English).book Page 301 Saturday, March 29, 2014 5:29 PM