User Manual

302
Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
32: Polysix Ensemble
This models the ensemble effect built into the classic Korg
PolySix programmable polyphonic synthesizer.
33: Stereo Flanger
This effect gives a significant swell and movement of pitch to the
sound. It is more effective when applied to a sound with a lot of
harmonics. This is a stereo flanger. You can add spread to the
sound by offsetting the phase of the left and right LFOs from
each other.
g: Feedback
h: Wet/Dry
The peak shape of the positive and negative “Feedback” value is
different. The harmonics will be emphasized when the effect
sound is mixed with the dry sound if you set a positive value for
both “Feedback” and “Wet/Dry”, and if you set a negative value
for both “Feedback” and “Wet/Dry”.
g: High Damp [%]
This parameter sets the amount of damping of the feedback in
the high range. Increasing the value will cut high-range harmon-
ics.
a
Depth 0...100 Sets the depth of the effect
Src Off...Tempo
Selects the modulation source that
will control the effect depth
Amt –100...+100
Sets the amount by which the effect
depth will be modulated
b
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
+
Polysix
Ensemble
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
a
Delay Time
[msec]
0.0...50.0
Sets the delay time from the original
sound
b
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the LFO
Waveform
c
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
d
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
e
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
f Depth 0...100
Sets the depth of LFO
modulation
g
Feedback –100...+100
Sets the feedback amount
High Damp [%] 0...100
Sets the feedback damping amount
in the high range
h
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Flanger
Flanger
Left
Right
Feedback
LFO Shape
LFO Phase
LFO: Tri / Sine
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
Pa300 User Manual v150 (English).book Page 302 Saturday, March 29, 2014 5:29 PM