User Manual

306
Effects
Modulation and Pitch Shift (Mod./P.Shift)
a: AUTOFADE Src
b: Fade-In Delay [msec]
b: Fade-In Rate
d: LFO Frequency Mod
When “LFO Frequency Mod” is set to AUTOFADE, you can use
the modulation source selected in “AUTOFADE Src” as a trigger
to automatically fade in the modulation amount. When “MIDI
Sync” is set to On, you cannot use this.
The “Fade-In Rate” parameter specifies the rate of fade-in. The
“Fade-In Delay” parameter determines the time from AutoFade
modulation source On until the fade-in starts.
The following is an example of fade-in where the LFO speed is
increased from “1.0Hz” to “4.0Hz” when a note-on message is
received.
AUTOFADE Src=Gate1, LFO Frequency Mod=AUTOFADE,
LFO Frequency [Hz]=1.0, Amt=3.0
The effect is off when a value for the dynamic modulation source
specified for the “AUTOFADE Src” parameter is smaller than 64, and
the effect is on when the value is 64 or higher. The AutoFade function
is triggered when the value changes from 63 or smaller to 64 or
higher.
40: St. Auto Fade Mod.
(Stereo Auto Fade Modulatiom)
This stereo chorus/flanger effect enables you to control the LFO
speed and effect balance using auto fade, and you can spread the
sound by offsetting the phase of the left and right LFOs from
each other.
AUTOFADE
AutoFade
Note On
All Note Off
Fade-In Rate
Source=Gate1
LFO Freq. Mod=AUTOFADE
LFO Frequency[Hz]=1.0 
Amount=+3.0
LFO Frequency
=1.0+3.0=4.0Hz
LFO Frequency
=1.0Hz
Gate1 Signal
AUTOFADE
Fade-In Dealy
a
AUTOFADE Src Off...Tempo
Selects the modulation source that
starts AutoFade
Fade-In Delay
[msec]
00...2000
Sets the fade-in delay time
Rate 1...100
Sets the rate of fade-in
b
LFO Frequency
Mod
D-mod,
AUTOFADE
Switches between D-mod and
AUTOFADE for the LFO frequency
modulation
Wet/Dry Mod
D-mod,
AUTOFADE
Switches between D-mod and
AUTOFADE for the effect balance
modulation
c
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the LFO
Waveform
d
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
e
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
f
L Delay Time
[msec]
0.0...500.0 Sets the left channel delay time
R Delay Time
[msec]
0.0...500.0 Sets the right channel delay time
g Depth 0...200 Sets the depth of LFO modulation
h
Feedback –100...+100
Sets the feedback amount
High Damp [%] 0...100
Sets the feedback damping amount
in the high range
i
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
AutoFade
LFO Frequency
FX Amt
Delay
Delay
Left
Right
Feedback
LFO Shape
LFO Phase
LFO: Tri / Sine
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
Pa300 User Manual v150 (English).book Page 306 Saturday, March 29, 2014 5:29 PM