User Manual

308
Effects
Modulation and Pitch Shift (Mod./P.Shift)
42: Doppler
This effect simulates the “Doppler effect” of a moving sound
with a changing pitch, similar to the siren of an passing ambu-
lance. Mixing the effect sound with the dry sound will create a
unique chorus effect.
a: LFO Mode
a: Src
b: LFO Sync
The “LFO Mode” parameter switches LFO operation mode.
When Loop is selected, the Doppler effect will be created repeat-
edly. If “LFO Sync” is set to On, the LFO will be reset when the
modulation source specified with the “Src” parameter is turned
on.
When “LFO Mode” is set to 1-Shot, the Doppler effect is created
only once when the modulation source specified in the “Src”
field is turned on. At this time if you do not set the “Src” param-
eter, the Doppler effect will not be created, and no effect sound
will be output.
The effect is off when a value for the modulation source specified for
the “Src” parameter is smaller than 64, and the effect is on when the
value is 64 or higher. The Doppler effect is triggered when the value
changes from 63 or smaller to 64 or higher.
e: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes away.
This parameter sets this pitch variation.
f: Pan Depth
This parameter sets the width of the stereo image of the effect
sound. With larger values, the sound seems to come and go from
much further away. With positive values, the sound moves from
left to right; with negative values, the sound moves from right to
left.
43: Scratch
This effect is applied by recording the input signal and moving
the modulation source. It simulates the sound of scratches you
can make using a turntable.
a
LFO Mode Loop, 1-Shot Switches LFO operation mode
Src Off...Tempo
Selects the modulation source of
LFO reset
bLFO Sync Off, On
Switches between LFO reset on and
off when LFO Mode is set to Loop
c
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
d
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
e
Pitch Depth 0...100
Sets the pitch variation of the
moving sound
Src Off...Tempo
Selects the modulation source of
pitch variation
Amt –100...+100
Sets the modulation amount of
pitch variation
f
Pan Depth –100...+100
Sets the panning of the moving
sound
Src Off...Tempo
Selects the modulation source of
panning
Amt –100...+100
Sets the modulation amount of
panning
g
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Pan Depth
D
-mod
+
Trigger
LFO Mode = 1-Shot
Doppler
LFO
a Scratch Source Off...Tempo
Selects the modulation source for
simulation control
b Response 0...100
Sets the speed of the response to
the Scratch Src
c
Envelope
Select
D-mod, Input
Selects whether the start and end of
recording is controlled via the
modulation source or the input
signal level
Src Off...Tempo
Selects the modulation source that
controls recording when Envelope
Select is set to D-mod
d Threshold 0...100
Sets the recording start level when
Envelope Select is set to Input
e Response 0...100
Sets the speed of the response to
the end of recording
fDirect Mix
Always On,
Always Off,
Cross Fade
Selects how a dry sound is mixed
g
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Pitch
Higher
Doppler - Pitch / Pan Depth
Lower
Original Pitch
Left
Center
Right
Pitch Depth
Pan Depth
< < < < < <<<<<< >>>>>> > > > > >
VolumeLouder
Louder
Pan Depth
= (–) value
Pan Depth
= (+) value
Input
D-mod
Envelope Select
D
-mod
Envelope Control
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
+
Scratch
Direct
Mix
D
-mod
Rec Control
Scratch
Pa300 User Manual v150 (English).book Page 308 Saturday, March 29, 2014 5:29 PM