User Manual

323
Effects
Delay
Appendix
67: St.BPM Mtap Delay
(Stereo BPM Multi tap Delay)
This four-tap delay enables you to select a tempo and rhythm
pattern to set up each tap.
68: St.BPM Mod. Delay
(Stereo BPM Modulation Delay)
This is a stereo modulation delay that lets you synchronize the
delay time to the tempo of the song.
aMode
Normal, Cross
Feedback,
Cross Pan1,
Cross Pan2
Switches the left and right delay
routing
b
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually for
this individual effect
Time Over? 1 ---, OVER!
Displays an error message when the
delay time for Tap1 exceeds the
upper limit
2 ---, OVER!
Displays an error message when the
delay time for Tap2 exceeds the
upper limit
c
Tap 1 Base
Note
r...w
Selects the type of notes to specify
the delay time for Tap1
Times x1...x32
Sets the number of notes to specify
the delay time for Tap1
d
Tap 2 Base
Note
r...w
Selects the type of notes to specify
the delay time for Tap2
Times x1...x32
Sets the number of notes to specify
the delay time for Tap2
e Tap1 Level 0...100
Sets the Tap1 output level
f
Feedback
(Tap2)
–100...+100 Sets the Tap2 feedback amount
Src Off...Tempo
Selects the modulation source of
the Tap2 feedback amount
Amt –100...+100
Sets the modulation amount of the
Tap2 feedback amount
g
High Damp [%] 0...100
Sets the damping amount in the
high range
Low Damp [%] 0...100
Sets the damping amount in the
low range
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
i
Spread –100...+100
Sets the width of the stereo image
of the effect sound
Src Off...Tempo
Selects the modulation source of
the effect sound’s stereo image
width
Amt –100...+100
Sets the modulation amount of the
effect sound’s stereo image width
j
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Left
Right
Feedback
Spread
FX Amt
FX Amt
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp
Low Damp
High Damp
Low Damp
Delay
Delay
Feedback
Tap1 Level
Mode
Mode
(1)
(2)
(1)
(2)
Tap1=(1)
Tap2=(2)
a
Modulation
Mode
LFO, D-mod
Switches between LFO modulation
control and modulation source
control
b
D-mod
Modulation
L/R:+/+,
L/R:+/–
Reversed L/R control by modulation
source
Src Off...Tempo
Selects the modulation source that
controls delay time
Response 0...30
Sets the rate of response to the
modulation source
c
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the LFO
Waveform
d
LFO Sync Off, On
Switches LFO reset off/on
Src Off...Tempo
Selects the modulation source that
resets the LFO
e
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
f
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
g
L LFO Phase
[deg]
–180...+180
Sets the phase obtained when the
left LFO is reset
Depth 0...200
Sets the depth of the left LFO
modulation
h
R LFO Phase
[deg]
–180...+180
Sets the phase obtained when the
right LFO is reset
Depth 0...200
Sets the depth of the right LFO
modulation
i
BPM(Delay)
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Time Over? L ---, OVER!
Display the error message if the left
channel delay time exceeds the
upper limit
R ---, OVER!
Display the error message if the
right channel delay time exceeds
the upper limit
j
L Delay Base
Note
r...w
Selects the type of notes to specify
the left channel delay time
Times x1...x32
Sets the number of notes to specify
the left channel delay time
Feedback –100...+100
Sets the feedback amount of left
delay
k
R Delay Base
Note
r...w
Selects the type of notes to specify
the right channel delay time
Times x1...x32
Sets the number of notes to specify
the right channel delay time
Feedback –100...+100
Sets the feedback amount of right
delay
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Left
Right
Feedback
LFO Phase
FX Amt
FX Amt
Stereo In - Stereo Out
LFO: Tri / Sine
Modulation Mode
D-mod
LFO
D
-mod
Delay
Delay
L/R: +/+ +/–
LFO Shape
Response
LFO Sync
Pa300 User Manual v150 (English).book Page 323 Saturday, March 29, 2014 5:29 PM