User Manual

348
Effects
Double Size
115: St. Mic + PreAmp
(Stereo Mic Modeling + PreAmp)
This is a stereo mic and preamp simulator (See “Mic Model+Pre-
Amp (Mic Modeling + PreAmp)” on page 298.). For example
you might use this to simulate micing of a stereo source such as a
rotary speaker.
116: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has six chorus blocks with different LFO phases. You
can produce a complex stereo image by setting a different delay
time and depth for each block. You can control the delay output
level via a modulation source.
b, c, d, e, f, g: Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→ Off (dm): Output level is switched from on to off depend-
ing on the modulation source.
Off→ On (dm): Output level is switched from off to on depend-
ing on the modulation source.
Combining these parameters, you can change from 4-phase cho-
rus to two-tap delay by crossfading them gradually via the mod-
ulation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the tap
outputs.
a
LFO Frequency
[Hz]
0.02...13.00 Sets the speed of the LFO
b
Tap1 (000)
[msec]
0...2000
Sets the Tap1 (LFO phase=0
degrees) delay time
Depth 0...30 Sets the Tap1 chorus depth
Status
Always On,
Always Off,
On Off (Dm),
Off On (Dm)
Selects on, off, or modulation source
for the control of Tap1 output
c
Tap2 (180)
[msec]
0...2000
Sets the Tap2 (LFO phase=180
degrees) delay time
Depth 0...30 Sets the Tap2 chorus depth
Status
Always On,
Always Off,
On Off (Dm),
Off
On (Dm)
Selects on, off, or modulation source
for the control of Tap2 output
d
Tap3 (060)
[msec]
0...2000
Sets the Tap3 (LFO phase=60
degrees) delay time
Depth 0...30 Sets the Tap3 chorus depth
Status
Always On,
Always Off,
On Off (Dm),
Off On (Dm)
Selects on, off, or modulation source
for the control of Tap3 output
e
Tap4 (240)
[msec]
0...2000
Sets the Tap4 (LFO phase=240
degrees) delay time
Depth 0...30 Sets the Tap4 chorus depth
Status
Always On,
Always Off,
On Off (Dm),
Off On (Dm)
Selects on, off, or modulation source
for the control of Tap4 output
f
Tap5 (120)
[msec]
0...2000
Sets the Tap5 (LFO phase=120
degrees) delay time
Depth 0...30 Sets the Tap5 chorus depth
Status
Always On,
Always Off,
On Off (Dm),
Off On (Dm)
Selects on, off, or modulation source
for the control of Tap5 output
Tube Pre AmpMic Simulation
Tube Pre AmpMic Simulation
Left
Right
FX Amt
Output Level
FX Amt
Stereo In - Stereo Out
Left
Right
Feedback
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
+
LFO: Triangle
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap5 Delay
Tap6 Delay
Tap4 Delay
D
-mod
On/Off Control
Panning Preset
g
Tap6 (300)
[msec]
0...2000
Sets the Tap1 (LFO phase=300
degrees) delay time
Depth 0...30 Sets the Tap6 chorus depth
Status
Always On,
Always Off,
On Off (Dm),
Off On (Dm)
Selects on, off, or modulation source
for the control of Tap6 output
h Panning Preset
1 : L 1 2 3 4 5 6 R,
2 : L 135 246 R,
3 : L 1 3 5 2 4 6 R,
4 : L 1 4 5 6 3 2 R
Selects the stereo panning pattern
for each tap
i
Tap1 Feedback –100...+100 Sets the Tap1 feedback amount
Src Off...Tempo
Selects the modulation source for
the Tap output level, feedback
amount, and effect balance
Amt –100...+100
Sets the modulation amount of Tap1
feedback amount
j
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Pa300 User Manual v150 (English).book Page 348 Saturday, March 29, 2014 5:29 PM