User Manual
Table Of Contents
- Let’s start!
- Playing and singing
- The SongBook
- Customizing and editing the Sound sets
- Customizing, recording and editing the Styles
- Customizing, recording and editing the Songs
- Customizing and editing the Sounds
- Listening and customizing the Sounds
- Editing the Sounds
- Setting the Sound’s basic parameters
- Setting the oscillator’s basic parameters
- Programming the Damper pedal
- Equalizing the Sound
- Setting the Drum Kit’s basic parameters
- Equalizing the Drum Kit
- Mixing and retriggering the drum samples
- Modulating pitch
- Programming the pitch envelope (Pitch EG)
- Programming the filters
- Modulating the filters
- Programming the filter envelope (Filter EG)
- Programming amplitude and pan
- Modulating amplitude
- Programming the amplitude envelope (Amp EG)
- Programming the LFO
- Adding effects to the Sound
- Sound Edit utilities
- AMS (Alternate Modulation Sources)
- Writing the Sounds
- Managing the User Samples
- The Effects
- Effects for the MIDI Sounds
- Adapting reverb to the room size
- Effects list
- DMS (Dynamic Modulation Sources)
- Dynamics (Dynamic)
- EQ and Filters (EQ/Filter)
- Overdrive, Amp models, and Mic models (OD Amp Mic)
- Chorus, Flanger, and Phaser (Cho/Fln Phaser)
- Modulation and Pitch Shift (Mod./P.Shift)
- Delay
- Reverb and Early Reflections (Reverb ER)
- Mono-Mono Serial (Mono-Mono)
- Double Size
- Limiter, Master EQ
- Effects for the MIDI Sounds
- Global settings, Preferences
- MIDI Connections
- MIDI
- Introduction to MIDI
- Quick settings using MIDI Presets
- MIDI communication settings
- Synchronizing Tempo with other instruments
- Programming the MIDI channels
- Installing the KORG USB MIDI Driver
- Connecting HAVIAN 30 to a personal computer or tablet
- Control Change messages
- Controlling the Styles and Player via MIDI
- MIDI
- File management
- Managing files
- Overview on file management
- Loading musical resources and settings
- Saving musical resources and settings
- Copying files and folders
- Deleting files and folders
- Selecting more items at once
- Formatting storage devices
- Backing up and restoring musical resources
- Connecting the internal drive to a personal computer
- Storage device management
- Exporting playlists
- Care of storage devices
- Managing files
- Appendix
Setting the Drum Kit’s basic parameters |343
Use the numeric field next to the sample name to choose the sample inside
the selected bank.
Bank Meaning
ROM Factory samples, supplied by KORG as standard.
RAM User samples, loaded when loading some User Drum Kits.
The sample you select for the current layer will be triggered by velocities
higher than the value of the velocity switches. If you do not wish to use veloc-
ity switching, assign just one layer to the selected key, and assign a sample
only to layer 1.
If the RAM drum sample is compressed, it will appear but will not sound.
▪ Select the Rev (Reverse) checkbox to play the sample in reverse. In the case
of samples that were originally specified to loop, the sample will be played
back in one-shot reverse mode. If the sample was originally set to reverse, it
will playback without change.
Setting a sample start offset
▪ Use the Ofs (Offset) parameter to specify the point where the sample will
start to play. With some samples this parameter will not be available.
Offset Meaning
Off The sound will start from the beginning of the sample.
1st…6th The sound will begin from the offset location pre-determined for
each sample.
NoAtk The initial portion of the multisample is ignored.
AMS Activates the Alternate Modulation Source (see below).
PseudoRandom (Only works when more than one Offset point is available in the
multisample). Randomly selects one of the available Offset points
(including Attack and Off).