User Manual
Table Of Contents
- Let’s start!
- Playing and singing
- The SongBook
- Customizing and editing the Sound sets
- Customizing, recording and editing the Styles
- Customizing, recording and editing the Songs
- Customizing and editing the Sounds
- Listening and customizing the Sounds
- Editing the Sounds
- Setting the Sound’s basic parameters
- Setting the oscillator’s basic parameters
- Programming the Damper pedal
- Equalizing the Sound
- Setting the Drum Kit’s basic parameters
- Equalizing the Drum Kit
- Mixing and retriggering the drum samples
- Modulating pitch
- Programming the pitch envelope (Pitch EG)
- Programming the filters
- Modulating the filters
- Programming the filter envelope (Filter EG)
- Programming amplitude and pan
- Modulating amplitude
- Programming the amplitude envelope (Amp EG)
- Programming the LFO
- Adding effects to the Sound
- Sound Edit utilities
- AMS (Alternate Modulation Sources)
- Writing the Sounds
- Managing the User Samples
- The Effects
- Effects for the MIDI Sounds
- Adapting reverb to the room size
- Effects list
- DMS (Dynamic Modulation Sources)
- Dynamics (Dynamic)
- EQ and Filters (EQ/Filter)
- Overdrive, Amp models, and Mic models (OD Amp Mic)
- Chorus, Flanger, and Phaser (Cho/Fln Phaser)
- Modulation and Pitch Shift (Mod./P.Shift)
- Delay
- Reverb and Early Reflections (Reverb ER)
- Mono-Mono Serial (Mono-Mono)
- Double Size
- Limiter, Master EQ
- Effects for the MIDI Sounds
- Global settings, Preferences
- MIDI Connections
- MIDI
- Introduction to MIDI
- Quick settings using MIDI Presets
- MIDI communication settings
- Synchronizing Tempo with other instruments
- Programming the MIDI channels
- Installing the KORG USB MIDI Driver
- Connecting HAVIAN 30 to a personal computer or tablet
- Control Change messages
- Controlling the Styles and Player via MIDI
- MIDI
- File management
- Managing files
- Overview on file management
- Loading musical resources and settings
- Saving musical resources and settings
- Copying files and folders
- Deleting files and folders
- Selecting more items at once
- Formatting storage devices
- Backing up and restoring musical resources
- Connecting the internal drive to a personal computer
- Storage device management
- Exporting playlists
- Care of storage devices
- Managing files
- Appendix
Delay |515
h High Damp [%] 0…10 0 Sets the damping amount in the high
range
Low Damp [%] 0…10 0 Sets the damping amount in the low
range
i Spread –100…+100 Sets the width of the stereo image of the
effect sound
j Wet/Dry Dry,
1:99…99:1,
Wet
Balance between the wet and dry signal
Src Of f…Tempo See DMS (Dynamic Modulation Source)
Amt –100…+100 Amount of modulation source
a: Control Target
This parameter selects no level control, delay output control (effect bal-
ance), or feedback amount control.
a: Polarity
b: Threshold
b: Offset
c: Attack
d: Release
The “Offset” parameter specifies the value for the “Control Target” pa-
rameter (that is set to None), expressed as the ratio relative to the param-
eter value (the “Wet/Dry” value with “Control Target”=Output level, or the
“Feedback” value with “Control Target”=Feedback).
When “Polarity” is positive, the “Control Target” value is obtained by multi-
plying the parameter value by the “Offset” value (if the input level is below
the threshold), or equals the parameter value if the input level exceeds the
threshold.
When “Polarity” is negative, Control Target value equals the parameter val-
ue if the input level is below the threshold, or is obtained by multiplying the
parameter value by the “Offset” value if the level exceeds the threshold.