Owner’s Manual (¬p.2) Manuel d’utilisation (¬p.6) Bedienungsanleitung (¬s.10) Manual de usuario (¬p.14) (¬p.18) 取扱説明書 Thank you for purchasing the Korg GA-50 GUITAR/BASS TUNER. To help you get the most out of your new instrument, please read this manual carefully. Merci d’avoir choisi la ACCORDEUR GUITARE/BASSE GA-50 de Korg. Afin de pouvoir exploiter au mieux toutes les possibilités offertes par l’instrument, veuillez lire attentivement ce manuel.
Parts of the GA-50 Tuning guide (Power) button GUITAR/BASS button Display Speaker FLAT button OUTPUT jack Internal mic SOUND button INPUT jack a. GUITAR/BASS indicator b. Note name c. Flat indicator d. Meter Installing the batteries Slide off the back cover of the GA-50 to open the battery compartment. Making sure to observe the correct polarity, insert the batteries, and then slide the back cover to close the battery compartment.
Tuning procedure Meter mode In this mode the VU style meter shown in the display is used to tune your instrument. 1. Connect the tuner. The connection method will depend on the type of guitar you’re connecting. When tuning an acoustic guitar If you’re using the internal mic, don’t connect anything. If you’re using a separately sold Korg CM-200 contact mic, connect the CM-200’s plug to the GA-50’s INPUT jack. When tuning an electric guitar or bass Use a commercially available cable with mono plugs.
5. Tune your instrument so that the VU style meter moves to the “ ” position (center) and the center tuning guide LED is lit (if using A=440 Hz as the reference pitch). The left indicator of the tuning guide will light if your instrument is flat, and the right indicator will light if your instrument is sharp. The pitch is flat. In tune. The pitch is sharp. Each marking in the meter scale corresponds to 2 Hz.
Specifications Tuning: 12 note equal temperament Detection range: Guitar B1 (46.25 Hz) – B6 (1975.53 Hz) Bass B0 (23.12 Hz) – B5 (987.77 Hz) Reference tone: Guitar 7B, 6E, 5A, 4D, 3G, 2B, 1E Bass LB (Low B), 4E, 3A, 2D, 1G, HC (High C) Tuning modes: Meter mode, Sound Out mode Flat tuning: 1 semitone ( ) – 5 semitones ( ) (semitone steps) Detection accuracy: ±1 cent Sound accuracy: ±1.
Parties du GA-50 Témoin du guide d'accordage Bouton (alimentation) Bouton GUITAR/BASS Affichage Haut-Parleur Bouton FLAT Prise OUTPUT Micro incorporé Bouton SOUND Prise INPUT a. indicateur GUITAR/BASS b. nom de la note c. indicateur bémol d. indicateur d’accordage Installation des piles Glissez le couvercle au dos du GA-50 pour accéder au compartiment à piles. Insérez les piles en respectant la polarité indiquée, puis remettez le couvercle en place.
Méthode d’accordage Mode Indicateur (Meter) En mode Indicateur, l’indicateur de style VU affiché sur l’affichage est utilisé pour accorder votre instrument. 1. Raccordez l’accordeur. La méthode utilisée dépendra du type de guitare raccordée. Pour accorder une guitare acoustique Si vous utilisez le micro incorporé, ne branchez rien. Si vous utilisez un microphone de contact Korg CM-200 vendu séparément, raccordez le CM-200 à la prise INPUT du GA-50.
4. Jouez une note sur votre instrument. Le nom de la note s’en rapprochant le plus apparaîtra sur l’affichage. Dans un premier temps, accordez votre instrument de façon que le nom de note correct s’affiche. 5. Accordez votre instrument de façon que l’aiguille de l’in- dicateur de style VU vienne se placer sur “ ” (centre) et que le témoin du guide d’accordage centrale s’allume (si vous utilisez A = 440 Hz comme hauteur de référence).
2. Appuyez sur le bouton FLAT pour choisir le nombre de demi-tons dont vous souhaitez transposer la note choisie vers le bas. (1 à 5 demi-tons). L’écran indiquera – Ce réglage n’est pas mémorisé lorsque vous éteignez l’appareil. 3. Accordez votre instrument de la manière habituelle en mode indicateur ou mode de sortie du son. Fiche techniques Gamme: 12 notes tempérament égal.
Teile des GA-50 Abstimm-LEDs (Einschalttaste)-Taste GUITAR/BASS-Taste Display Lautsprecher FLAT-Taste OUTPUT-Buchse Internes Mikrofon SOUND-Taste INPUT-Buchse a. Anzeige GUITAR/BASS b. Notenname c. Nullwertanzeige d. Stimmanzeige Einsetzen der Batterien Schieben Sie die Rückseite des GA-50 wie in der Abbildung gezeigt nach oben, um das Batteriefach zu öffnen. Achten Sie beim Einsetzen der Batterien auf die korrekte Polung und schieben Sie die Rückseite wieder zu.
Arbeitsweise für das Stimmen Meter-Modus In diesem Modus wird die Stimmanzeige im Display benutzt, um Ihr Instrument zu stimmen. 1. Scließen Sie das Stimmgerät an. Die Anschlussmethode ist je nach verwendeter Gitarre unterschiedlich. Beim Stimmen einer akustischen Gitarre Wenn Sie das interne Mikrofon verwenden wollen, schließen Sie nichts an. Wenn Sie einen getrennt erhältliches Korg CM-200 Kontaktmikrofon verwenden, schließen Sie den Stecker des CM-200 an die INPUT-Buchse des GA-50 an.
4. Spielen Sie eine Einzelnote auf dem Instrument. Das Display zeigt den Namen der erkannten Note sowie die Oktave, in der sie gespielt wird, an. Stimmen Sie Ihr Instrument so weit, dass schon einmal der richtige Notenname angezeigt wird. 5. Stimmen Sie Ihr Instrument so, daß die VU-Skala in der Position „ “ steht (Mitte) und die Abstimm-LEDs leuchten (wenn Sie A = 440 Hz als Referenztonhöhe benutzen).
2. Drücken Sie FLAT-Taste, um die Anzahl der Halbtöne auszuwählen, um die die zuvor ausgewählte Note reduziert werden soll. Dieser Versatz wird folgendermaßen (1-5 Halbtöne tiefer). angezeigt: – Diese Einstellung bleibt nicht erhalten, wenn das Gerät ausgeschaltet wird. 3. Stimmen Sie Ihr Ihnstrument auf normale Weise entwe- der im Meter-Modus oder im Ton-Ausgabe-Modus.
Partes del GA-50 LEDs de afinación Botón (alimentación) Botón GUITAR/BASS Pantalla Altavoz Botón FLAT Jack OUTPUT Micrófono incorporado Jack INPUT Botón SOUND a. I ndicador GUITARR A/ BAJO b. Nombre de la nota c. Indicador bemol d. Medidor Instalar las pilas Quite la tapa posterior del GA-50 deslizándola para abrir el compartimento de las pilas. Asegurándose de que lo hace con la polaridad correcta, inserte las pilas y vuelva a poner la tapa posterior para cerrar el compartimento de las pilas.
Procedimiento de afinación Modo de Medidor En este modo, el medidor en pantalla se utiliza para afinar el instrumento. 1. Conecte el afinador. El método de conexión dependerá del tipo de guitarra que conecte. Al afinar una guitarra acústica Si utiliza el micrófono incorporado, no tiene que conectar nada. Si utiliza un micrófono de contacto Korg CM-200 (se vende por separado), conecte el conector del CM-200 al jack INPUT del GA-50.
5. Toque una nota en su instrumento, y afínelo de modo que la aguja apunte al centro “ “ y el indicador de afinación esté iluminado (si se utiliza A = 440 Hz como el tono de afinación de referencia). Si el instrumento está por debajo de la nota, se iluminará el indicador de la izquierda. Si está por encima, se iluminará el indicador de la derecha. El tono está bajo. Afinado. El tono está alto. Cada marca en la escala del medidor corresponde a 2 Hz.
3. Afine el instrumento siguiendo el método habitual con el modo Medidor o el modo Salida de sonido.
各部の名称 チューニング・ガイド (電源)ボタン GUITAR/BASS ボタン ディスプレイ スピーカー FLAT ボタン OUTPUT 端子 内蔵マイク SOUND ボタン INPUT 端子 a. GUITAR/BASS表示 b. 音名表示 c. フラット表示 d.
チューニングの方法 メーター・モード ディスプレイのメーターでチューニングするモードです。 1.
5. 楽器を単音で鳴らして、メーターが“ ”の位置(中央)を 指し、チューニング・ガイドの中央のランプが点灯する ようにチューニングします( A=440Hzを基準にする場 合)。チューニング・ガイドは、音が低いときは左、高い ときは右のランプが点灯します。 低い方に ずれているとき チューニングが 合っているとき 高い方に ずれているとき また、メーターの1目盛は2Hz相当に対応しています。 例えば、A=436Hzを基準に各弦を調整する場合は、各 弦を“440”から2目盛下がった位置に調整します。 内蔵マイクを使用するときは、マイクに楽器をでき るだけ近づけ、チューニング中に余計な音が入らな いようにしてください。 サウンド・アウト・モード 基準音を鳴らしてチューニングするモードです。 1.「メーター・モード」の手順2、3を設定します。 2.
仕様 音律: 12平均律 測定範囲: Guitar B1 Bass B0 (46.25Hz)~ B6(1975.53Hz) (23.12Hz)~ B5(987.77Hz) 基準発振音: Guitar 7B、6E、5A、4D、3G、2B、1E Bass LB(Low B)、4E、3A、2D、1G、HC(High C) チューニング・モード: メーター・モード、サウンド・アウト・モード フラット・チューニング: 1半音( )~ 5半音( 測定精度: )の半音ステップ ±1セント以内 サウンド精度: ±1.5セント以内 接続端子: INPUT端子(φ6.3モノラル標準ジャック) OUTPUT端子(φ6.