User Manual and Operating Guide

107
DriveProtected
■ The selected removable disk (e.g., magneto-optical
disk) is write protected.
→ Remove the disk, and turn off write protection.
IllegalDrive/Operation
■ The operation you attempted was not appropriate for
the selected drive. For example, this message will
appear if you attempted to eject a non-removable disk,
or if you attempted to load the system from a drive that
did not contain the system.
→ Select an appropriate drive or operation.
IllegalTo-EndTime
■ When using the expand/compress track editing opera-
tion (“ExpCmpTrk”), the TO and END settings could
not be executed for the IN–OUT region.
→ Set the TO–END region so that it is 50–200% of the IN–
OUT region.
InTime>=OutTime
■ When using track editing, auto punch-in/out record-
ing, or looping, the IN and OUT settings you made
were incorrect so that the operation could not be exe-
cuted. This message will appear if IN is later than OUT,
or if they are at the same time location.
→ Change the IN and OUT times to the correct settings.
ToTime>=EndTime
■ When using the expand/compress track editing opera-
tion (“ExpCmpTrk”), the TO and END settings you
made were incorrect so that the operation could not be
executed. This message will appear if TO is later than
END, or if they are at the same time location.
→ Set the times correctly.
MemoryFull
■ There is insufficient memory for recording or track edit-
ing.
→ Delete unneeded data.
In some cases, you can solve this problem by turning
the power off and then on again.
MIDIOverflow
■ When receiving MMC or recording MIDI Clock, a MIDI
data reception failure occurred.
→ Delete unneeded data from the transmitting device.
NumberOfTracks
■ During track editing, the number of source tracks is dif-
ferent than the number of destination tracks.
→ Make settings so that the source and destination have
the same number of tracks.
■ Since “Clip” contains no data, data cannot be copied.
→ Either copy data to “Clip,” or select a different copy
source track.
SongProtected
■ The selected song is protected.
→ Either turn off protect (→p.60), or select a different
song.
TempoFast
■ When recording tempo, the tempo was too fast to be
recorded correctly.
→ If you are recording MIDI clock, set the tempo of the
MIDI transmitting device (sequencer etc.) to a slightly
slower setting.
→ If you are recording tap tempo, please tap at a slightly
slower tempo.
TempoSlow
■ When recording tempo, the tempo was too slow to be
recorded correctly.
→ If you are recording MIDI clock, set the tempo of the
MIDI transmitting device (sequencer etc.) to a setting of
 =40 or faster.
→ If you are recording tap tempo, please tap at a slightly
faster tempo.
The system software of the D16 can be updated by
installing the new version from a disk that contains the
new D16 system file.
The latest system file can be downloaded from the
Korg website (http://www.korg.co.jp).
For details on system files, refer to the Korg website or
to Korg information.
1. Downloading the system
Download the system file from the Korg website. Copy
the file onto an external DOS format removable disk.
For details on the procedure, refer to the Korg website.
2. Connections
Connect the external removable disk drive containing
the system file to the D16 via SCSI. (→p.48)
Be sure to turn off the power of both devices before
you make connections.
3. Updating the system
1 Select the drive connected to the D16.
In the [SYSTEM] “DiskUtil” tab page, use “Drive
ID” to select the drive that contains the system file.
2 Use “SelOperation” to select “LoadSystem.”
3 Execute the load operation.
Press the “Exec.” button. When the display asks
“AreYouSure?” press the “Yes” button to begin
loading.
If the power is turned off accidentally while the sys-
tem is being loaded, the D16 may become incapable
of operating correctly. If this occurs, please contact
Korg dealer.
4 When loading is completed, the following display
will appear, and the loaded system will be checked.
If the check results are correct, the display will indi-
cate “Check sum=OK.” If not, it will indicate
“Check sum=NG.”
If the result is “NG,” please re-start, and execute the
load operation once again.
If “NG” appears again, please contact Korg dealer.
5 After a short time, the D16 will restart automati-
cally, and will begin operating with the new system.
Updating the system
software
Appendices
Messages
Upda
tin
g
th
e
sys
t
e
m