Operation Manual

119
Program operating mode
Page 16 - Amp EG
Amp envelope
Start/Attack/Break/Sustain/Release Level
Theseparametersarethelev e loftheenvelopesegment.
0…99 Levelvalue.
Start Level
Thisparameterspecifiesthevolumelevelatnote‐on.If
youwantthenotetobeginataloudlevel,setthistoa
highvalue.
Attack Level
This parameter specifies the volume level that will be
reachedaftertheattacktimehaselapsed.
Break Level
This parameter specifies the volume level that will be
reachedafterthedecaytimehaselapsed.
Sustain Level
This parameter specifies the volume level that will be
maintainedfromaftertheslopeti mehaselapseduntil
note‐offoccurs.
Attack/Decay/Slope/Release Time
Theseparametersspecifythetimeoverwhichthevol‐
umechangewilloccur.
0…99 Timevalu
e.
Attack Time
Thisparameterspecifiesthetimeoverwhichthevolume
willchangeafternote‐onuntilitreachestheattacklevel.
Ifthestartlevelis0,thiswillbetherisetim eofthesound.
Decay Time
This parameter sp ecifies the time over which the vol‐
umewillchangefrom whenitreachesthe att
acklevel
untilitreachesthebreakpointlevel.
Slope Time
This parameter sp ecifies the time over which the vol‐
umewillchangefromwhenitreaches thebreakpoint
lev
eluntilitreachesthesustainlevel.
Release Time
This parameter sp ecifies the time over which the vol‐
umewillchangeafternote‐offuntilitreaches0.
Amp EG ‘Level’ modulation
AMS(L) (Alternate Modulation Source)
Thisparameterspecifiesthesourcethatwillcontrolthe
“Level” parameters of the amp EG. See “A M S  (Al ter‐
nateModulationSource)list”onpage12
3.
Intensity
Thisparameterspecifiesthedepthanddirectionofthe
effect that “AMS” willhave. For example,if“A M S ”  is
Velocity, setting “Start Level Swing”, “Attack Le
vel
Swing”and“BreakPointLev
elSwing”to+andsetting
“Intensity” to a positive (+) value will cause the amp
EG volume levels to increase as you play more
strongly. Setting “Intensit y” to a negative (–) values
willcausetheampEGvolumelevelstodecreaseasyou
playmore strongly. With asetting of 0, the  lev
els will
beasspecifiedon“P
age16‐AmpEG”.
‐99…+99 Intensityvalue.
Start Level Swing
Thisparameterspecifiesthedirectioninwhich“AMS”
willchange“StartLevel”.If“Intensity”issettoaposi‐
tive (+) val
ue, setting this parameter to + will
 allow
AMStoincreasetheEGlevel,andsettingthisparame‐
terto–willallowAMStodecreasetheEGlevel.Wi
tha
settingof0,nochangewilloccur.
Attack Level Swing
Thisparameterspecifiesthedirectioninwhich“AMS”
willchange“AttackLevel”.If“Intensity”issettoapos‐
itive (+
) value, settin
g this parameter to + will allow
AMStoincreasetheEGlevel,andsettingthisparame‐
terto–willallowAMStodecreasetheEGlevel.Wi
tha
settingof0,nochangewilloccur.
Break Point Level Swing
Thisparameterspecifiesthedirectioninwhich“AMS”
willchange“BreakLevel”.If “Intensity”issettoapos‐
itive (+) va
lue, settin
g this parameter to + will allow
AMStoincreasetheEGlevel,andsettingthisparame‐
terto–willallowAMStodecreasetheEGlevel.Wi
tha
settingof0,nochangewilloccur.
Note-on
Note-off
Attack
Time
Decay
Time
Release Time
Attack Level
Sustain
Level
Time
Break Point
Start
Level
Slope
Time
Amplifier EG
Volume
Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note when Start
Level Swing=0 and Attack Level
Swing and Breack Level Swing
are set to +
Strongly played note when
Start Level Swing=0 and Attack
Level Swing and Breack Level
Swing are set to +
Strongly played note when
Start Level Swing=0 and Attack
Level Swing and Breack Level
Swing are set to +