User's Manual
Table Of Contents
- A few words from Greg Mackie.
- Selecting channels for a Mute Group.
- MAIN MIX (L/R) fader.
- Group Master Section.
- BREAK button/indicator
- MONITOR section
- STEREO IN knob
- Meter section.
- FX Master Section.
- Talkback.
- A better way.
- A traditional Monitor Mix.
- Musician's Phones.
- Aux Master AFL buttons and indicator.
- Aux Master.
- Master Control Section
- Further reading about mixing.
- A few more tips on equalization.
- MID EQ (stereo channels)
- Source Mic / Line (stereo channels).
- PFL switch / indicator
- Same as Mono Channels
- Different than
- Channel fader
- Bus Assign switches
- —20 (Signal present) LED.
- Mute button/ indicator.
- Pan.
- FX Send.
- Aux PRE Switch.
- Aux Sends
- EQ (Equalization), Mono Channels
- Comp (Compressor) and indicator.
- Gain Control.
- Mono Channel Strips.
- Channel 25-26 (or Channels 17-18) and Phones
- Musician Phones (AUX OUT 3 OR 4 + L/R INJECT)
- Aux Out.
- Group Out (sub buses).
- Monitor Out.
- Main Out.
- Talkback input.
- Foot Switch input.
- USB Out
- USB In
- USB input / output.
- Stereo input channels.
- Mono input channels.
- Power input connector
- POWER switch
- Power supply section
- Why do we start with the back of the mixer?
- How the band is set up on the mixer.
- The "pusha-bunch-'0' buttons" approach to creating a mute group.
- Un-doing the "pusha-bunch-'0' buttons" approach to creating a mute group.
- Program a Mute Group…
- Rack mounting (MW-2408 only)
- Settings that can be saved
- More on Factory Reset (restoring the factory default settings).
- Other GLOBAL options.
- Recalling a Global Scene
- Saving a Global Scene
- Global menu (scene memory, settings, initialization).
- Locking the state of the feedback suppressor
- Feedback Suppressor: Seting routing options.
- Recalling an Equalizer Setting (continued)
- Recalling an Equalizer Setting.
- Saving Equalizer settings.
- Adjusting (Narrow Mode) Continued
- Adjusting EQ Narrow Mode EQ (31 /9-band).
- Adjusting 9-band EQ (Wide Mode).
- Selecting Narrow or Wide 9-band equalization.
- Recalling a Dynamics preset.
- Saving a Dynamics setting.
- FEEDBACK SUPPRESSOR
- EQUALIZATION
- SoundLink Signal Processing*
- Gee, they don't sound like effects!
- Recalling a DFX preset.
- Saving a Digital Effects setting.
- Using the TAP button to set the delay time.
- Editing an effect
- Applying a Digital Effect
- Selecting the DFX type
- Digital Effects (DFX).
- Saving and Recalling Mute Groups.
- Combining Hard Mutes and Mute Groups.
- Adding to or subtracting channels from a Mute Group.
- Creating a Mute Group.
- "Hard muting".
- OL (Overload) LED.
Hook-up/Back panel Analog Controls Digital Controls
Stereo Channels • Same and Dierent
Analog Controls
24
PFL switch /
indicator
Enables ( ) or
disables (
) the
PFL (pre-fader listen) function.
If this button is enabled, the
signal before adjustment by the
channel fader (“pre-fader”) is
output sent to the
PHONES jack
and the
MONITOR OUT output
jacks.
When in the Enable position,
the indicator is lit.
.
Stereo channels have a few dif-
ferent controls and many identi-
cal ones.
Dierent than
Mono Channels
■ TRS stereo Line inputs
■ Mic/Line switch
■ No Compressor function
■ 2-band fixed MID EQ
■ Shared channel controls (9/10, 11/12
combined etc.)
Same as Mono Channels
■ Input Gain
■ Hi Eq
■ Lo Eq
■ Aux Sends
■ FX
■ Pan
■ Mute
■ OL & -20 LEDs
■ Bus Assign switches
■ 60mm fader
■ PFL switch
Source Mic /
Line (stereo
channels).
Switches the
channel setting
according to the
input jack(s)
used.
Set this to
MIC
(
) if using the
rear panel
MIC
IN
jack.
Set it to
LINE
(
) if using the LINE IN jack(s).
The MIC IN jack and LINE
IN jack cannot be used at
the same time.