Table of Contents Precautions ................................................................ 4 Introduction ............................................................... 5 Welcome! ......................................................................... 5 Main features ................................................................... 5 Front and rear panel .................................................. 5 Front panel .......................................................................
Precautions Location Using the unit in the following locations can result in a malfunction. • In direct sunlight • Locations of extreme temperature or humidity • Excessively dusty or dirty locations • Locations of excessive vibration • Close to magnetic fields Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended.
AX3A Owner’s manual Introduction Welcome! Thank you for adding the TONEWORKS AX3A Modeling Signal Processor to your r ig. Whether you’re playing live or in the studio, or practicing with headphones, the AX3A will give you countless hours of great sounds! To ensure a long and trouble-free relationship with your AX3A, please read this manual carefully, and use it as directed. When you’ve finished reading this manual, please keep it for future reference.
position, and Edit mode when at the [PRE FX]–[DELAY/REV-PARAM] positions. Rear panel 4 2. Program/Value display In Edit mode, this display indicates the effect type (F0–F9, LE, nr, nF), the parameter (P1–P4) or its setting (value). In Write mode or Program mode, the display indicates the program number. When BYPASS/MUTE is active, the display indicates the name of the note you’re tuning. Connect your guitar to this jack. In Effect mode, use these buttons to switch effect types or parameters.
AX3A Owner’s manual 1. Slide the cover of the battery case in the direction of the arrow, and open the cover. Insert four separately sold AA-size alkaline batteries, being sure to observe the correct polarity (“+” and “-” markings), and close the battery case. 2. When using batteries, the power will turn on when you insert a guitar cable into the AX3A’s INPUT jack. While the power is on, the display will indicate the program number or other information.
In Program mode you can instantly switch between sounds by pressing the Program Up/Down switches to change programs. To enter Program mode, set the function selector to [PROGRAM]. (The LEDs in the upper part of the Program Up/Down switches will light.) Selecting a program 1. Make sure that the function selector is set to [PROGRAM]. In Program mode, the LEDs of both the Program Up and Program Down switches will be lit.
AX3A Owner’s manual By adjusting the main parameters, you can tweak your sound to what you have in mind. cycle the display through LE (program level), nr (NR sensitivity), and nF (notch filter). Use the value knob to adjust each parameter. Selecting and adjusting sub-parameters and [TONE] parameters LE: Use the value knob to adjust the program level (0–10). A setting of 7.0 is the standard value. Some effect settings may cause clipping. If this occurs, lower the program level.
3. Use the value knob or the Program Up/Down switches to select the program in which you want to save your settings. 4. Press the [▲(WRITE)] button once again. The program will be saved, ” briefly. and the program/value display will indicate “ The newly saved program will overwrite (i.e., replace) the existing settings, so that the previous program in that location will be lost. If you decide not to save the new program, press the [CANCEL] button to cancel the operation.
AX3A Owner’s manual Never turn off the power while reloading. guitar is farther from the correct pitch. When in tune, both the Program Up and Down LEDs will light. Adjusting the tuner calibration When you turn on the power, the built-in tuner is set to a reference pitch of A 440 Hz (concert pitch). You can calibrate this reference pitch in a range of 438 Hz–445 Hz. You can use the [▲]/[▼] buttons to calibrate this in the range of 438 Hz–445 Hz.
❑ Is the master volume turned down? Set the function selector to [PROGRAM], and turn the value knob to adjust the master volume. 3. Effects don’t apply ❑ Could an effect be bypassed? ❑ Is the modulation “DEPTH” or the delay/reverb “MIX” set to a low value? ❑ Could the [MIC&BODY] DEPTH be set to 0? ❑ Is the AX3A in Bypass mode? Refer to “Bypass and Mute” (p.10) and cancel the Bypass function. 4.
Sommaire Précautions .............................................................. 14 Introduction ............................................................. 15 Bienvenue! ..................................................................... 15 Caractéristiques principales ............................................ 15 Panneau Avant et Arrière ......................................... 15 Panneau Avant ............................................................... 15 Panneau Arrière ..................
Précautions Emplacement L’utilisation de cet instrument dans les endroits suivants peut en entraîner le mauvais fonctionnement. • En plein soleil • Endroits très chauds ou très humides • Endroits sales ou fort poussiéreux • Endroits soumis à de fortes vibrations • A proximité de champs magnétiques Alimentation Veuillez brancher l’adaptateur secteur spécifié sur une prise secteur à la tension appropriée.
AX3A Manuel d’utilisation Introduction Bienvenue! Merci d’avoir choisi l’AX3A. pour garantir un fonctionnement sans problèmes, veuillez lire attentivement ce manuel et utiliser l’appareil comme expliqué. Quand vous aurez fini de lire le manuel, conservez-le de façon à pouvoir vous y reporter par la suite.
1. Sélecteur de fonction 5. Commutateur Program Up La fonction de ce potentiomètre dépendra du mode sélectionné par le sélecteur. Vous êtes en mode Programme lorsque le sélecteur est sur la position (PROGRAM), en mode d’écriture lorsque le sélecteur est sur la position (WRITE) et en mode d’édition lorsque le sélecteur est sur la position [PRE FX]–[DELAY/REV-PARAM]. Dans le mode Programme, utilisez ce commutateur pour sélectionner un programme.
AX3A Manuel d’utilisation 3. Prise pour pédale d’expression Si vous souhaitez utiliser une pédale d’expression au pied pour commander le volume ou le Wah-Wah, vous pouvez connecter une pédale Korg optionnelle EXP-2 ou XVP-10 sur cette prise. 4. Prise d’alimentation secteur Raccordements Mettre les appareils que vous souhaitez raccorder hors tension et baissez toutes les commandes de volume. 1. Connectez un câble jack sur la prise OUTPUT de l’AX3A à un amplificateur, mixeur ou enregistreur.
Exemple de branchement à une console de mixage ou d’un enregistreur Ecouteurs Guitare OUTPUT Casque INPUT 3. Appuyez sur le commutateur Program Up ou Down pour sélectionner un programme. L’afficheur Program/Value indiquera le numéro du programme. Enregistreur numérique Bloc d'alimentation secteur á connecter sur le secteur Jouer (Mode Programme) Les réglages de chaque effet est communément appelés programme. L’ AX3A possède 80 programmes. Les programmes 01–40 sont réinscriptibles.
AX3A Manuel d’utilisation L’afficheur Program/Value indiquera une valeur F0–F9 et la diode au dessus du commutateur Program Down s’allumera, indiquant que l’afficheur Program/Value montre le type d’effet. La liste d’effets imprimée sur le panneau avant vous indique le type d’effet sélectionné. Vous pouvez tourner le bouton Value pour régler le paramètre principal pour l’effet sélectionné.
nF: Ce bouton permet de régler le filtre Notch (oF, 1-63) de réduction de la rétroaction acoustique. Tournez le bouton pour spécifier la fréquence de coupure minimisant la rétroaction acoustique. Le filtre Notch sera désactivé si vous tournez le bouton complètement à gauche. Tournez ce bouton vers la droite pour déplacer la fréquence de coupure vers le haut et trouver le point où la rétroaction acoustique survient.
AX3A Manuel d’utilisation Accordeur Retour aux réglages d’usine L’ AX3A possède un accordeur chromatique automatique. Vous pouvez ajuster le pitch de référence entre A438 Hz–A445 Hz. Procédure pour l’accord 1. L’accordeur chromatique automatique est activé quand l’ AX3A est en position Bypass ou Mute. Si vous voulez accorder sans produire de sons, comme par exemple lors d’un concert, vous voudrez probablement mettre l’AX3A en position Mute. 2. Jouez une note avec votre guitare.
❑ Avez vous branché un câble stéréo dans l’entrée de l’appareil? Quand il est utilisé sur piles, l’alimentation n’est pas désactivée quand un cable stéréo est branché. Veillez à n’utilioser que des câbles monos. ❑ Est ce que l’adaptateur secteur est compatible? ❑ Est ce qu’il est bien connecté à la prise alimentation? ❑ Peut-il être en panne? 5. Le son de votre ampli est saturé ou le son est mauvais.
Inhalt Vorsichtsmaßregeln ................................................. 24 Einleitung ................................................................ 25 Willkommen! ................................................................. 25 Funktionen ..................................................................... 25 Bedienoberfläche und Rückseite ............................... 25 Bedienfeld ...................................................................... 25 Rückseite ...........................
Vorsichtsmaßregeln Verwendungsort Bei Verwendung des Geräts an den folgenden Orten kann eine Fehlfunktion auftreten. • Im direkten Sonnenlicht • An Orten mit extremer Temperatur oder Luftfeuchtigkeit • An sehr staubigen oder schmutzigen Orten • An Orten mit starker Vibration • In der Nähe von Magnetfeldern Stromversorgung Schließen Sie das spezielle Netzteil an eine Netzsteckdose mit der richtigen Netzspannung an.
AX3A Bedienungsanleitung Einleitung Willkommen! Vielen Dank für deine Entscheidung zu einem AX3A ModelingSignalprozessor der TONEWORKS-Serie. Wir sind uns ziemlich sicher, dass du damit Stunden lang in Sound-Orgien schwelgen wirst – sei es live, im Studio, oder beim Üben mit einem Kopfhörer! Um über Jahre hinweg Freude an deinem neuen AX3A zu haben und es richtig zu bedienen, musst du dir diese Bedienungsanleitung vollständig durchlesen. Bewahre sie an einem Ort auf, wo du sie bei Bedarf wieder findest.
1. Funktionswahlschalter 6. Program Down-Schalter Die Funktion der Up/Down-Taster und des Eingaberads richten sich nach dem hier eingestellten Modus. Stelle den Schalter auf [PROGRAM], um den Program-Modus zu wählen oder auf [WRITE], um Einstellungen zu speicher n. Zum Editieren wählst du eine der Positionen [PRE FX]~[DELAY/REV-PARAM]. Im Program-Modus kann hiermit der benötigte Speicher gewählt werden. Bei wiederholtem Drücken dieses Schalters wird der jeweils vorangehende Speicher gewählt.
AX3A Bedienungsanleitung Wenn du mit einem Kopfhörer arbeiten möchtest, musst du ihn an die OUTPUT-Buchse anschließen. Vorbereitung Einlegen der Batterien 2. Verbinde die Gitarre mit der INPUT-Buchse auf der Rückseite. Damit schaltest du im Batteriebetrieb das Gerät ein. 3. Ein (optionales) AC-Netzteil musst du zuerst mit der DC9V-Buchse auf der Rückseite und danach mit einer Steckdose verbinden. 4. Jetzt kannst du auf dem Verstärker (Mixer) die Lautstärke einstellen.
Spielen (Program-Modus) Die Einstellungen eines gespeicherten Sounds nennen wir „Program“. Das AX3A bietet 80 solcher Speicher. In den Speichern 01~40 kannst du eigene Einstellungen sichern. Die Speicher 41~80 enthalten „Presets“, die dir auf die Sprünge helfen sollen. Im Programm-Modus kann sofort zwischen Sounds umgeschaltet werden, die Programm höher/niedriger Pedale gedrückt wird, um Programme umzuschalten.
AX3A Bedienungsanleitung Um den gewählten Effekt auszuschalten, musst du die Taster [▲] und [▼] simultan drücken. Wenn der Effekt aktiv ist, wird der Typ angezeigt. “ angezeigt. Ist er hingegen aus, so wird „ ■ Praxis Bei Anwahl eines Effekts lädt das AX3A immer die Idealeinstellungen für dessen Parameter. Du kannst also schon erstklassige Sounds erzielen, indem du einfach für jede Kategorie (PRE FX, MIC&BODY, MOD und DELAY/REV) einen anderen Effekt wählst.
(F0~F9, P1~P4). Drücke den Program Up-Schalter, damit der Parameterwert angezeigt wird. Praktisch für schnelle Kontrollen… Speichern eines Sounds (Write-Modus) Wenn du mit einem Sound zufrieden bist, kannst du ihn wie folgt speichern. Wenn du allerdings vorher einen anderen Speicher wählst bzw. das Gerät ausschaltest, werden deine Einstellungen wieder gelöscht! 1. Stelle den Funktionswahlschalter auf [WRITE]. Effektumgehung und Stummschaltung Zum Einstellen des Verstärkers, beim Stimmen bzw.
AX3A Bedienungsanleitung 2. Spiele eine Note auf der Gitarre. Im Speicher-/Werte-Display erscheint der Name der erkannten Note. Die Notennamen werden folgendermaßen angezeigt: Notenname C C# D D# E F F# G G# A A# B Anzeige 3. Wenn deine Gitarre zu hoch gestimmt ist, blinkt die Diode des Program Up-Schalters. Ist sie zu tief gestimmt, so blinkt die Diode des Program Down-Schalters. Je schneller eine Diode blinkt, umso weiter bist du von der richtigen Tonhöhe entfernt.
❑ Hast du das AC-Netzteil an die DC9V-Buchse auf der Rückseite angeschlossen? ❑ Hast du das Netzteil an eine geeignete Steckdose angeschlossen? ❑ Ist das Netzteil eventuell beschädigt? 2.
Appendices F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 44 PRE FX COMP LIMITER SLOWATK XCITER WAH VIB/PH CH/FLN DRONE OCTAVE RINGMOD MIC&BODY C-MIC M-LARGE M-SMALL G-LARGE G-SMALL T-LARGE DRY NYLON STEEL RESO Main Parameter SENS 1...10 RATIO 0...10 ATTACK 0...10 FREQ 1...10 MANUAL 1...10 SPEED 1...10 SPEED 1...10 KEY A...G' EFFECT 0...10 OSCFREQ 0...10 Main Parameter DEPTH 0...10 DEPTH 0...10 DEPTH 0...10 DEPTH 0...10 DEPTH 0...10 DEPTH 0...10 DEPTH 0...10 DEPTH 0...10 DEPTH 0...
TONE P1 TREBLE P2 -15...15 LEVEL/NR/NOTCH MIDDLE F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 MOD CL CHO MT CHO CL FLN BI CHO DUO PH TREM ROTARY PITCH RND FILT FILTRON Main Parameter SPEED 1...10 SPEED 1...10 SPEED 1...10 SPEED1 1...10 SPEED1 1...10 SPEED 1...10 SPEED 1...10 PITCH -12...12 SPEED 1...10 SENS/POL 0...10,-0...-10 DELAY/REVERB ECHO+ MLT HD MOD DLY ST DLY PP DLY SLAP SPRING PLATE ROOM HALL MID FREQ LE PROGRAM LEVEL F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 P3 -15...15 Main Parameter MIX 0...10 MIX 0...
Preset program chart Program No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 46 Program name FOLK1 FOLK2 FOLK3 CONFESSOR LOWRIDER BLUES1 BLUES2 BLUES3 EC OOO DRONE MY CHORUS BI CHORUS EQ & MT CHO DUO PHSE TREM RESO SLOWATK MOD DLAY BOSSA AC ECHO+ WATERFILTER Body type C-MIC M-LARGE G-SMALL T-LARGE C-MIC G-LARGE BODY STEEL M-SMALL STEEL C-MIC T-LARGE Body OFF/EQ ON G-SMALL RESO NYLON G-LARGE NYLON M-LARGE STEEL Program No.
4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan C 2006 KORG INC.