Installation Sheet

INSTALLATION INSTRUCTIONS
Item#P1542, P1543, P1544-688-L (New. 03/07/2020)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
PREPARATION
(Fig.1)
1. Shut off
power at the fuse box or circuit breaker box and remove
the old fixture including the mounting hardware.
2.
Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care no
t to misplace any small parts necessary
for installation.
3. Secure mounting plate (A) to the outlet box using s
crews (B)
(Size: 8-
32*1/2”L). The side of the mounting plate marked
“GND” must face out.
CONNECTING THE WIRES (Fig.2)
4. Connect the electrical wires
as shown in Fig. 2, making sure that
all wire connectors are secured. If your outlet has a ground wire
(green or bare copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly to the
mounting plate (A) using the g
reen screw provided. After wires
are connected, tuck them carefully inside the outlet box.
5. Place the fixture’s back
plate (C) over the mounting plate (A)
and secure with screws (D).
FINISHING THE INSTALLATION (FIG.1)
6. Slide the glass shade (H) into the front bracket (E). A
ttach glass
holders (F) to the front bracket (E) with screws
(G) to secure the
glass to fixture.
CAUTION/ATTENTION:
When handling the fixture, do
not apply pressure to the LEDs, hold the fixture by the
base or front bracket (E) only.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps
for more details (Fig 3.)
a. Shut off the power.
b. Remove screws (D) and fixture body from mounting plate
(A).
Disconnect wire connectors
and place fixture body on a clean
surface.
c. Loosen screws (G) to remove glass holders
(F) and glass shade
(H).
d. Press the button of the printed “L” quick connect
or on LED
module (J) with screwdriver (not included)
to disconnected the
black wire
and then disconnect the white wire from the printed
“N” quick connector on LED module (J).
e. Remove plastic screws (I). Carefully remove LED module (J).
f. Reverse steps b-e for installing the new LED module.
For better heat dissipation, the LED module (J
) should be
applied with thermal grease when re-lamping.
Your installation is now complete. Return power and
test the fixture.
Note: Illustration (Fig.1) on this manual is for
installati
on purposes only. It may or may not be
identical to the fixture purchased.
Dimmable with LED compatible wall dimmer switches.
LA-3220E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTUR
E
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set# A-020-102A
-Mounting Plate
-Ground Screw
-Mounting Screw*2
D
J
I
G
F
H
E
C
Screw driver
IMPORTANT: FIXTURE SHOULD BE INSTALLED
BY A QUALIFIED ELECTRICIAN TO ENSURE
PROPER WIRING AND INSTALLATIO
N.
G
F
H
D
E
A
B
C