Installation Sheet

ManualsBrandsKovacs ManualsLightingGroovin 12" Tall Integrated LED Outdoor Wall Sconce with Glass Shade

Mounting plate(1)(Part#A-020-118)

Ground screw (1)

Mounting screw (2)

Fig.4

INSTALLATION INSTRUCTIONS

For Model # P1761-L/P1762-L

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION

(Fig.

)

1. Shut off power at the circuit breaker and remove the old fixture, including

the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clear area.

Take care not to lose any parts necessary for installation.

3. Unscrew the screws (G) and separate the mounting plate (B) (Part #

A-020-118) from back plate (H).

4. Attach the mounting plate(B) to the outlet box (not provided) with the two

outlet box screws (C) (Size: 8-32*1”).

Note: the side of mounting plate marked “GND” must face out.

CONNECTION THE WIRES (Fig. 2)

5. Connect the electrical wires as shown in (Fig.2), making sure that all wire

connectors (D) are secured. If your outlet has a ground wire (green or bare

copper), connect the fixture ground wire to it. Otherwise, connect the fixture

ground wire directly to the mounting plate using the green screw provided.

FINISHING THE INSTALLATION (Fig.1)

6. Align back plate (H) onto mounting plate (B) and secure with the screws (G).

7. To prevent moisture from entering the outlet box and causing shortage, use

clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline the outside of

fixture back-plate where it meets the wall leaving space at bottom to allow

moisture a means to escape. (Fig.3)

8. Bulb information: (2 x AC LED 6W included for P1761-L and 2 x AC LED 6W

included for P1762-L.)

DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. Return power to the junction box and

test the fixture.

Replacing LED module (Fig. 4)

The LED module can be replaced by a qualified electrician and shut off the

power at the circuit breaker and remove fixture from the outlet box without

cutting of wire and without damage to any decorative element to which the

fixture is attached. See installation steps for more details (Fig 4.)

a. Shut off power.

b. Take the back plate (H) off from wall and unscrew cover (K) from fixture

cage.

c. Remove the broken LED Module (I) for re-lamping by unscrewing screws (J)

and taking wire connectors (L) out of pre-drilled hole of the heatsink panel

and loosening the connectors (L).

d. Use wire connectors (L) and screws (J) to secure new LED modules (I), and

then put wire connectors (L) back into the pre-drilled hole.

Note: 1. The LED module should be provided by a specified supplier.

2. Please twist this cut of the bottom cap facing back when

installing.

Fig.1

IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED

ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

Fig.4

(HOT) (NEUTRAL)

HOUSE

WIRES

BLACK

HOUSE

WIRES

WHITE

BARE COPPER(GROUND)

HOUSE

GREEN OR

WIRES

FIXTUREFIXTURE

WIRES

FIXTURE

WIRES

BARE

(GROUND)

COPPER

WHITE

RIBBED

BLACK

SMOOTH

GREEN OR

Fig.2

WIRES

Fig. 3

Caulking

Backplate