2’x14’ Alexander Hardtop Gazebo With Double Roof Assembly Manual Kozyard LLC Products www.kozyard.com © Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.
Warnings and Cautions • Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo. • Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds. • Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage. • Some parts may have sharp edges or corners.
Attention: Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.
P2 x2 P12 x2 Q4 x2 Q13 x2 Q14 x2 R x8 S x128 W12 x2 W11 x2 W13 x2 W14 x2 T2 x2 W15 x2 T4 x2 U1 x4 U6 x4 U3 x4 V11 x2 V43 x2 V44 x2 U4 x4 V12 x2 V45 x2 V46 x2 ITEM P2 P12 Q4 Q13 Q14 R S T2 T4 U1 U3 U4 U6 V11 V12 V43 V44 V45 V46 W11 W12 W13 W14 W15 W16 W17 W18 W16 x2 W17 x2 W18 x2 DESCRIPTION QTY 2 2 2 2 2 8 128+2 2 2 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Finishing Bar Net Frame Finishing Bar Net Frame Net Frame Finishing End Spacer Finishing Bar Finishing Bar Solidifying Bar Iron A
# x80+2 6# x8+1 7# x36+2 X41 x2 X42 x2 X43 x2 9# x24+2 X44 x2 10# x4+1 11# x12+1 12# x12+2 X45 x2 X46 x2 X47 x2 Allen key X48 x2 Wrench SY x4 S3 x2 S4 x2 Y3 x2 Y4 x2 Z x76 Z1 x4 Z2 x4 Z3 x2 Z4 x2 4# x120+2 1# x246+4 2# x16+2 3# x16+2 ITEM DESCRIPTION X41 X42 X43 X44 X45 X46 X47 X48 S3/S4 Y3/Y4 SY Z Z1 Z2 Z3 Z4 1# 2# 3# 4# 5# 6# 7# 9# 10# 11# 12# Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Alexander 12’X14’ assembly manual Solid Sidewa
Parts Required: Step 1: Set up Poles 1. Set up Poles (Part A) with Stand Plates (Part L) using screws 1# as shown in the diagram. A A X4 A x4 1# x12 1# 1# 1# L x4 L L Reference for anchoring gazebo: • • If the ground is concrete and its depth is over 3 inches, you can purchase 3/8" diameter x 3" length sleeve anchors. Only anchor after finishing all the assembly.
Parts Required: C6 x2 B6 x2 F x4 E7 x2 D7 x2 1# X24 Step 2: Connect the Beams 1. Connect (Part C6,B6) into one beam using Union bar (Part F) with screws 1# as shown in the diagram. Short Beam Overall: C6 X2 B6 F B6 B6 C6 X2 C6 1# F 1# 1# 1# 2. Connect (Part E7,D7) into one beam using Union Bar (Part F) with screws 1# as shown in the diagram.
Parts Required: 1# x96 B61 x2 C61 x2 B62 x2 C62 x2 E71 x2 D71 x2 D72 x2 E72 x2 Step 3: Connect Joint Bars and Tracks with Beams B61 C61 C6 C62 B6 E71 B62 D71 E7 D7 E72 D72 1. Connect Joint Bars (Part C61,C62), Tracks (PartE71,E72) to Beams (Part C6 and E7) using screws 1# as shown in the diagram. C6,E7 X2 Tip: Do not tighten all screws on the Jointer bars (Part B61, C61, E71, D71) until the screws of the roof panels are aligned in place. 1# 1# C62,E72 C61,E71 B6,D7 2.
Parts Required: 2# 3# x16 x16 Step 4: Set up Poles and Beams X8 Use screws 3# first, then use screw 2# to connect Poles and Beams together as shown in the diagram. 3# 3# ① A B6 X2 C6 Tip: Place parts on carpet or rug to avoid scratches during assembly. A ② 2# C6 ② B6 B6 E7 ① C6 X8 2# D7 X2 C6 D7 A E7 B6 E7 B6 3+ Tip: At least three people for this step.
Parts Required: J1 x4 1# J2 x4 J1 x32 J2 1# 1# 1# Step 5: Connect Solidifying Bars with Beams and Poles X4 Affix the frame with Corner Solidifying Bars (Parts J1, J2) using screws 1# as shown in the diagram. J1 J2 J1 Diagonal 1 J2 ona l2 J2 Diag J1 J2 J1 Diagonal 1 = Diagonal 2 Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.
Parts Required: 9# x24 H x4 G x4 9# 9# G H 9# ① X4 ② X4 Step 6: Cover the connections 1. Finish connecting the beams using Corner Covers (Part G) and screws 9# as shown in the diagram. ① 2. Affix the middle beams using Joint Cover (Part H) and screws 9# and 1# as shown in the diagram.
Parts Required: H2 x1 Step 7: Seal the seams 1. After finishing Step 6, apply silicone rubber to the seams to ensure they're watertight. 2. If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap screws with silicone rubber isn't necessary.
Parts Required: 4# x120 1# x4 H1 x4 Step 8: Install Hooks After inserting Hooks (Part 4#) into the tracks, secure them by placing the Joint Cover (Part H1) to lock them in place. ② ① 4# X4 4# 4# Note the amount of hooks for each slot as noted below: 4# H1 1# H X2 ① Put 7 hooks in each slot of sidewall track (part C62, Part B62). 4# ② H1 x7 x7 B6 C6 C62 B62 X2 Put 8 hooks in each slot of sidewall track (part E72, Part D72).
Parts Required: 12# x12 M1 x4 M2 x4 K4 x1 1# x12 Step 9: Connect Corner Roof Bar “M3” Connect the Short Corner Roof Bar (Part M1) with Long Corner Roof Bar (Part M2) using screws 1# and washer 12#.. M1 M2 Tip: The combination will be called “Part M3” in following steps.
Parts Required: P2 x2 R x4 1# x16 Q4 x2 1. Connect the Inner Roof Connector(Part K4) with the Corner Roof Bar (Part M3) using screws 1#. 1# X4 M3 K M3 M3 M3 M3 2. Attach Corner Roof Bar(Part M3) to main frame using screw 1# as shown in the diagram. ② M3 R 1# 1# ① X4 3. Attach Finishing Bar (Part P2, Q4) with Finish End (Part R) using screws 1# to Corner Roof Bar (Part M3) as shown in the diagram. M3 Q6 X4 ② K4 ① P2 M3 P2 Q4 M3 2+ Tip: At least two people for this step.
Parts Required: N1 x2 N4 x2 1# x12 Upward View N4 1# N1 N1 1# 1# 1# K4 N4 ① 1# N1 or N4 Step 11: Set up Roof Bar X4 Attach Roof Bar (Part N1,N4) to main frame using screw 1#. Attention: The part N4 must be placed on the 14’ side.
Parts Required: K14 x1 1# x2 Upward View 1# K14 1# K4 Step 12: Connect Outside Roof Connctor Connect Outside Roof Connctor (Part K14) to inside roof (Part K4) using screw 1# as shown in the diagram.
Parts Required: Z3 V11 V12 V43 V44 V45 H3 x1 Z4 V46 Step 13: Snap Bracket Snap Bracket (Part Z, Z1, Z2, Z3, Z4) to the roof panel edges as shown in the diagram. (with snaps facing upwards) X2 Z1 Z2 Z Z Z2 Z1 V11 V12 Z Z Z Z Z3 Z4 V43 V44 V45 V46 Tip: 1. Wearing protective gloves is recommended. 2.
Parts Required: T2 x2 T4 x2 V46 R T2 1# 1# R x4 T4 V45 x8 V44 V43 R V12 V 11 T2 V 11 V12 R R V43 V44 1# V45 V46 T4 1# Step 14: Assemble Roof Panel 1. Push the Roof Panels (Part V11, V12, V43, V44, V45,V46) up to the upper roof as shown in the diagram. 2. Attach Finishing Bars (Part T2, T4) to the upper roof with Finish End (Part R) using screws #1, as shown in the diagram.
Parts Required: U1 x4 U6 x4 1# U3 x4 x24 U1 U6 U1 U6 U1 U4 x4 ② ② U1 U6 U6 ① Attention: If the holes on the Solidifying Bar (Part U1, U6) and the hole of the roof panel cannot be aligned, please adjust or loosen screw 1# until the screws of the roof panel are in place. Step 15: Connect Solidifying Bars Attach Solidifying Bars ( Part U1, U6) to Roof Bar or Corner Roof Bar using Iron Angle (Part U3, U4) and screws 1# as shown in diagram.
Parts Required: x32 W11 x2 W12 x2 W13 x2 W14 x2 W15 x2 W16 x2 H3 x1 W17 x2 W18 x2 Step 16: Snap Bracket Snap Brackets (Part Z) to roof panel edges as shown in the diagram. (with snaps facing upwards) X2 Z Z Z Z Z Z Z Z Z W11 W12 W13 W14 Tip: 1. Wearing protective gloves is recommended. 2.
Parts Required: x32 X41 x2 X42 x2 X43 x2 X44 x2 X45 x2 X47 x2 X46 x2 H3 x1 X48 x2 Step 17:Snap Bracket Snap Brackets (Part Z) to roof panel edges as shown in the diagram. (with snaps facing upwards) X2 Z Z Z Z Z Z Z Z Z X41 X42 X43 X44 Tip: 1. Wearing protective gloves is recommended. 2.
Overall roof assembly: Please place the panels on the frame and assemble them from the centerline (Part N1,N4) to the left and right. X3 W18 W17 W16 N1 X5 X4 X2 X1 W15 W14 N4 X6 W13 X7 W12 W11 X8 W11 W12 W13 W14 W15 X42 X44 X41 W16 N1 X43 X45 X46 X47 X48 N4 W17 W18 Tip: Wearing protective gloves is recommended.
Parts Required: 5# x80 S x128 6# x8 7# x36 10# x4 Step 18: Affix roof panels using screws and Spacers (Part S) as shown in the diagram. 10# Align all roof panels and screws LOOSELY (DO NOT TIGHTEN ANY SCREWS) until all the roof panels are aligned accordingly. THEN, TIGHTEN all screws to secure the roof panels in place. S ① X4 S ② 6# X8 ② ① ② 6# ① ④ ④ ③ ④ ③ ④ X36 X80 ④ ③ 5# 7# 2+ Tip: At least two people for this step.
Parts Required: P12 Q13 x2 Q14 x2 Q13 11# x12 1# x4 Q14 Upward View P12 P12 Q14 Q 13 Step 19: Assemble Net Frame Attach Net Frames (Part P12, Q13, Q14) to Finishing Bars (Part P2, Q4) using screws (1#, 11#) as shown in the diagram. Q13 Q14 11# 1# 11# Perspective: X2 11# 11# 11# P12 1# 11# X2 Q13 Q14 P12 Q14 Q13 N4 N1 Tip: The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P12, Q13, Q14) more effectively.
Parts Required: S3 x2 Y3 x2 S4 x2 Y4 x2 Step 20: Assemble Net and Sidewall Install the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.
Parts Required: SY X4 Step 21: When closing the Mosquito Net, refer to the steps below to align it with the poles, as shown in the diagram. ① S3,S4 ⑤ ③ ④ Y3,Y4 ② SY S3,S4 S3,S4 Y3,Y4 Y3,Y4 S3,S4 S3,S4 Y3,Y4 Care and Warranty • Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period. Don't hesitate to contact us directly if you are missing parts or need a replacement. 66 Kozyard LLC © Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.