Aluminum-Steel 10’x10’ Pergola Assembly Manual Kozyard LLC Products www.kozyard.com © Copyright 2016 - 2022 Kozyard LLC. | All Rights Reserved.
Use the hex keys in the box. You may need to use a drill for this step. Three or more people are required at this stage. 3+ You may need a ladder. Do not tighten screws all the way for now. Pergola10’X10’ ANCHOR BLUEPRINT 273cm/ 8.96' 25x25cm/9.8"x9.8" 273cm/8.96' 12.5cm/4.9" 249cm/8.13' 249cm/ 8.
A B C D 4X 1X 1X 2X Pole A1 2X Side Tube B1 1X Side Tube C1 Side Track Tube 1 or 3 Position Short Pole A2 2X 2 or 4 Position Short Pole Side Tube 1X Side Tube D1 2X Side Track Tube E 1X Middle Track Tube E1 1X F 2X Beam Tube F1 2X G 1X Still Round Tube G1 1X Still Round Tube H 5X Moveable Round Tube H1 5X Moveable Round Tube 4X Plate Page 2 Middle Track Tube Beam Tube J 140X+5X Bolt
K Bolt +1x O Hook L Bolt +1x P Hook M Bolt 32X+2X R Lock N Hook S Canopy 8 6 Allen Key Q V1 2x Connector Ribbon T U 16x +2x V2 5x Connector X 4x V 8x Connector Plastic Cover OVERALL G&G1 H&H1 B&B1 2 2 C&C1 X X Page 3 X
St ep 1 A 4X First Remove plastic plugs from Part A1/A2 and Part A. A1 / A2 A A1 2X A2 2X Then Place Part X on four Poles (Part A) and connect A and (A1 or A2) by using Bolt J to attach the four Poles. J X 4X J A X4 V 8X A1 / A2 X M6x 16 J 64X X A J J A1 / A2 S6 Q 1X V Don't tight the bolts too much when you insert A into A1 and A2. 3 Position Short Pole S t ep 2 Connect Part I and four Poles by using Bolt J.
St ep3 Connect B, and B1 using Bolt J to build Main Beam 1 . B 1X J V1 J B1 1X B J C 1X J C1 1X B1 B R 2X Connect C and C1 using Bolt J to build Main Beam 2. Meanwhile attach Part R to C using Bolt J.
St ep 4 Connect Main Beam 1 and Main Beam 2 with the four Poles using Bolt M. M 6x 15 M 16X X4 A1 B/B1 / A2 OR C/C1 M S8 Q 1X B1 B A2 C A1 C1 A A St ep 5 D 2X X2 1. Insert Hook N into the slot of Part D. Repeat twice. X5 N E 1X N 10X D 2. Insert Hook P and Hook O into the slot of Part E. Please be certain to insert Hook P with this method.
Step 6 Connect D and D1 to build the Cross Beam (D and D1) by using Bolt J D 2X J J X2 D1 2X D1 V2 D J J V2 2x D1 D M6x16 J 16X S6 Q 1X Step 7 Connect the Cross Beam (D and D1) with the four Poles using Bolt M.
Step 8 J J E 1X 1. Connect E and E1 by using Bolt J to build the Cross Beam (E and E1). E1 E1 1X V2 E J J F 2X E1 E F1 2X J X2 J J 24X 2. Repeating the same method use F and F1 to build the Cross Beam (F&F1). M6x16 F1 F V2 S6 J J Q 1X F1 F V2 3x Step 9 M6x85 Connect the Cross Beams (E and E1) and (F and F1) with Main Beams 1 and 2. Attention: Always keep Hook P and C/C1 in the same side.
Step 10 Insert G, G1, H, and H1 into the canopy from its side G 1X G1 G G1 1X H 5X H H1 5X S H1 S H S 1X Step 11 M6x16 Connect G and G1with B,and B1 using bolt K, Hold the canopy with the frames. K B/B1 J 10X H&H1 G & G1 M6x30 K 3X S6 C/C1 X10 X5 Q 1X H1 J 3.Connect the canopy and 2.Pull the line from the canopy the Hook using Bolt J and put on hook to tighten the canopy. Page 9 H 1.
Step 12 C/C1 R T 1X TOP FA B RIC S E T P Hook Part T onto Hook P Step 13 Stabilize Part T to beam B/B1 in order to fasten Top Fabric .
Step 14 U 16X Secure Foot I to the ground using Part U. U X4 I Step 15 In the end,Please make sure all screws are compeletly fixed before using.
66 Kozyard LLC 10808 6th ST, Unit 100, Rancho Cucamonga, CA 91730
