0’x12’ Odyssey Permanent Gazebo with Double Roof Assembly Manual Kozyard LLC Products Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.
+ 1. Two or more people are required for assembly. 2. You will need one or more step ladders. 3. Wearing protective gloves is recommended. 4. You may need a safety hat. 5. Use the hex keys included in the box. 6. Please use a Phillips screwdriver. 7. Do not fully tighten screws until assembly is completed. 8. For ease of construction, you may need to use a drill. Odyssey 10x12' ANCHOR BLUEPRINT 353m/11.6' 30x30cm/11.8"x11.8" 289cm/9.5' 15cm/5.9" 259cm/8.5' 323cm/10.
POLE BEAM BEAM BEAM BEAM CORNER ROOF BAR ROOF BAR FINISHING BAR FINISHING BAR FINISHING BAR FINISHING BAR FINISHING BAR FINISHING BAR ROOF BAR FINISHING BAR SOLIDIFYING BAR
SOLIDIFYING BAR SOLIDIFYING BAR FINISHING BAR FINISHING BAR CORNER SOLIDIFYING BAR FINISHING BAR CORNER SOLIDIFYING BAR INSIDE ROOF CONNECTOR FINISHING END PLATE CORNER COVER OUTSIDE ROOF CONNECTOR SUPPORTING PART JOINT COVER SUPPORTING PART FINISHING END FINISHING END PANELS PANELS PANELS PANELS PANELS PANELS PANELS PANELS PANELS PANELS
PANELS SOLID SIDEWALL PLASTIC LOCK HOOK M6 16 M6 12 MOSQUITO SIDEWALL JOINT COVER 158 17 SCREWS SCREWS M6 15 8x SCREWS Step 1: SCREWS Set up poles (Part A) with plates (Part B) using screws #1 as shown in diagram.
Step 2: Connect Part C and C1 into one beam using screws #1 as shown in diagram. C 2x C1 C1 2x C 1 C1 C2 2x C C3 2x M6x12 1 16x S4 6 Connect Part C2 and C3 into one beam using screws #1 as shown in diagram.
Step 3: 2 Use screws #1, #2 and #3 to connect poles and beams as shown in diagram.
Step 4: Affix the frame with corner solidifying bars (Part L and L1) by using screws #1 as shown in diagram.
X x104 Step 5： M5x10 4x AA x4 ② ① ① ② Step 5, After you finish putting the hooks into the tracks, secure part AA using screws #5. This locks the hooks into place.
Step 6: Finish connecting beams using corner covers (Part M) and screws #4 as shown in diagram. 4 5 4 4 4 5 Affix middle beams using joint cover (Part N) and screws #4 and #5 as shown in diagram.
Step 7: Set up roof frame. 12 Affix the supporting part (Part P) to the corner roof bar using screws #1 6 Step 8: 12 6 Connect the inside roof connector (Part Q) with the corner roof bar (Part D) using screws #1 as shown in diagram. Attach the corner roof bar (Part D) and main frame using screws #1 as show in diagram.
Step 9: M6x12 2 6 2 Attach Roof Bars (Part E) to inside roof connector and main beam using Screws 1#&2# as shown in diagram.
Step 10: Connect the outside roof connector (Part Q1) to inside roof (Part Q) using screw #2 as shown in diagram. 2 2 2 M6x12 10x M6x16 2 3x 6 Affix finishing bars (Part F, F1 and F2) to roof bars (Part D & E) using fnishing end (Part R and R1) and screws #1 and #2 as shown in diagram.
Step 11: Insert panels (Part T,T1 and T2) into the slots of roof bars as shown in diagram. Step 12: M6x12 6 Affix finshing bars (Parts G, G1 and G2) to roof bars (Part E and D) using finishing end (Part R and R2) and screw #1 as shown in diagram.
Step 13: Affix roof bars (Parts H and H1) to beam using supporting part (Part S) and screws #1 as shown in diagram. M6x12 6 Insert roof bars (Part H and H1) to the slot of corner roof bar (Part D) as shown in diagram.
Step 14: Affix solidifying bars (Parts J and J1) to corner roof bar (Part D) using screw #1 as shown in diagram. M6x12 6 Affix solidifying bars (Parts J and J2) to roof bar (Part E) using screw 1# as shown in diagram.
Overall Roof Assembly U 4x V2 U U1 4x V V U1 W1 W V1 V3 V V1 U U1 4x V1 4x Attention: Start from V and install piece by piece in a clockwise sequence. Only V2 4x W and W1 can joinly insert into the slot. Fit V2 and V3 from top to the slot.
Step 15: U 4x V W V2 W1 V3 V1 2. Only after the sheet metal fits well into the slot, then install part Y to fix it. V2 V3 U1 4x Y V2 V 4x U V V1 4x V2 4x H E V3 4x V W 2x E E W1 2x V2 W1 V3 Y 20x 15 W1 1. Insert V into the slot of H and E, then put V2 from above to the slot and join with V.
Step 16: 4 M6X12 4 6 Affix finishing bars (Parts K, K1 and K2) to roof bars using finishing end (Part R and R2) and screws as shown in diagram.
Step 17 : Hang up solid sidewall as shown in diagram.
Step 18: X4 When you close the curtain, please tie fabric strape to poles as shown in diagram. Z Z There are three ways to secure your netting and curtains to the legs using the 4 included ties： 1.) Securing just the netting. 2.) Securing netting and curtains. 3.) Use all ties for windy conditions. In the end, check all screws are fastened tightly before using.
Support: Toll Free: 1-866-355-0018 www.kozyard.com email: support @kozyard.com Kozyard LLC 2825 80Th AVE SE, Suite 202 Mercer Island, WA 98040 © Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.
