Kramer Electronics, Ltd.
Contents Contents 1 2 3 3.1 3.2 3.3 3.4 4 5 5.1 5.2 5.3 5.4 5.
ADDENDUM (this data is included at the end of the Overview section) This addendum adds the following information to the user manual: Caution – No operator-serviceable parts inside unit. Warning – Use only the Kramer Electronics input power wall adapter that is provided with this unit1. Warning – Disconnect power and unplug unit from wall before installing or removing device or servicing unit.
Introduction 1 Introduction Welcome to Kramer Electronics (since 1981): a world of unique, creative and affordable solutions to the infinite range of problems that confront the video, audio and presentation professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 350-plus different models now appear in 8 Groups1, which are clearly defined by function.
Overview The other unit is fed over the same CAT5 cable. The Power Connect feature applies as long as the CAT5 cable is heavy gauge cable (that is, it can carry power). The distance does not exceed 50 meters on standard cable. For a distance of 100 meters, separate power supplies must be connected to the transmitter and to the receiver simultaneously, unless using heavy gauge CAT5 cable. 3.
Your WP-211DS 3.
Your WP-211DS Table 1: WP-211DS Front Panel Features Feature Function XGA INPUT 2 HD15F Connector DEFAULT SELECT Switch IN 2 Green LED Connects to the computer graphics source 2 Slide to left for input 2, slide to right for input 1 Lights when the XGA INPUT 2 source is active 4 5 6 7 8 IN 1 Green LED XGA INPUT 1 HD15F Connector AUDIO IN 2 mini plug Connector AUDIO IN 1 mini plug Connector Red LED Lights when the XGA INPUT 1 source is active Connects to the computer graphics source 1 Connects to audio
Using the WP-211DS 5 Using the WP-211DS For details of how to: Install your WP-211DS, see section 5.1 Wire the CAT5 LINE IN / LINE OUT RJ-45 connectors, see section 5.2 Connect your WP-211DS, see section 5.3 Select the default master source signal, see section 5.4 Connect the REMOTE connector, see section 5.5 You can use your WP-211DS, for example, in a conference room, as the example in Figure 3 illustrates: Figure 3: Example of a Conference Room WP-211DS Installation 5.
Using the WP-211DS 5.
Using the WP-211DS 5.3 Connecting the WP-211DS To connect your WP-211DS, do the following: 1. Connect a computer graphics (master) source to the XGA INPUT 1 HD15F connector and to the AUDIO IN 1 3.5mm mini jack, for example, using a Kramer C-GMA/GMA cable1. 2. Set the DEFAULT SELECT switch to IN 1 (the factory preset default) or IN 2, as section 5.4 describes. 3. Connect a second computer graphics source to the XGA INPUT 2 HD15F connector and to the AUDIO IN 2 3.
Using the WP-211DS 5.4 Operating using the Default Master Source Signal Selection The DEFAULT SELECT switch is factory preset to IN 1 and the WP-211DS will detect the presence of the master source signal at the XGA INPUT 1 connector. If you connect active sources to both the XGA INPUT 1 and the XGA INPUT 2 connectors, the source at the XGA INPUT 1 connector takes priority over the source at the XGA INPUT 2 connector and it is routed to the XGA OUT and the AUDIO OUT connectors (audio follows the video).
Using the WP-211DS 5.5 Connecting the REMOTE Connector You can force the routing of one of the 2 inputs to the XGA output by remote control. To do so, connect the appropriate REMOTE input terminal block connector pins to a dry contact switch1. For example, as Figure 6 illustrates, to route REMOTE IN 1 to the XGA output, connect PIN 1 to the Ground. To route REMOTE IN 2 to the XGA output, connect PIN 2 to the Ground pin.
Technical Specifications 6 Technical Specifications Table 4 includes the technical specifications: 1 Table 4: Technical Specifications of the WP-211DS INPUTS: 2 XGA on HD15F connectors 2 unbalanced stereo audio on 3.5 mm mini audio connectors OUTPUTS: 1 XGA (RGBHV) on a 10 PIN terminal block connector 1 XGA on an HD15F connector (input #1 loop) 1 unbalanced stereo audio on a 3 PIN terminal block connector 1 CAT5 (for video) on an 8 PIN terminal block connector MAX.
LIMITED WARRANTY Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product.
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing. Caution Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.
