Kramer Electronics, Ltd.
Contents Contents 1 2 2.1 3 4 4.1 5 5.1 5.2 5.
Introduction 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 1,000-plus different models now appear in 11 groups 1 that are clearly defined by function.
Getting Started 2.1 Quick Start This quick start chart summarizes the basic setup and operation steps.
Overview 3 Overview The SL-1 is a highly versatile controller that acts as an all-in-one extended remote control panel for control of A/V equipment—especially projectors and associated equipment—in any room (such as classrooms, boardrooms, or auditoriums). It streamlines operations and simplifies control by integrating audio, video, and computer-video sources into a centralized system.
Your SL-1 Master Room Controller 4 Your SL-1 Master Room Controller Figure 1 and Table 1 define the unit. Figure 1: SL-1 Master Room Controller Table 1: SL-1 Master Room Controller Functions # 1 2 3 4 Feature RELAYS Terminal Blocks IR Output Terminal Blocks RS-232 Terminal Blocks ETHERNET RJ-45 Connector 5 DEFAULT Pushbutton 6 K-NET 2 Terminal Block 7 8 9 10 12V DC Connector IR IN Sensor and LED IR INPUT 3.
Connecting the SL-1 Master Room Controller # 11 12 13 14 15 16 17 Feature K-NET LED RS-232 Tx/Rx LEDs IR LEDs RELAYS LEDs SRVC DIP-Switch K-NET TERM DIP-Switch PROGRAM USB Connector Function Illuminates when the K-NET is active Illuminates while transmitting/receiving on an RS-232 port (1 to 2) Illuminates when an IR port is active Illuminates when an relay is active (1 to 3) Slides down for service use only, slides up for normal operation Slides down for K-NET termination, slides up for not terminated Co
Connecting the SL-1 Master Room Controller Figure 2: Connecting the SL-1 Master Room Controller 5.
Connecting the SL-1 Master Room Controller 5.2 Connecting the Ethernet Port The Ethernet connection of the SL-1 allows you to perform all control functions of the SL-1 over the Internet using a PC running the Kramer Site-CTRL control program. To connect the SL-1 to a network: 1. Connect the Ethernet port of the SL-1 to the Ethernet port on a network hub or network router, via a straight cable with RJ-45 connectors. 2. At the other end, connect the Internet to a PC running Site-CTRL.
Operating the SL-1 Master Room Controller 6 Operating the SL-1 Master Room Controller You can operate your SL-1 using: • A K-Net compatible remote controller or auxiliary control panel: To operate your device using an external K-Net device, see the K-Config Configuration Guide 1 • The optional RC-4 Infrared remote control transmitter: To operate your device using the infrared remote controller, see the User Manual packed with the remote controller • A PC running Site-CTRL control software: To operate your
LIMITED WARRANTY Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product.
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing. Caution Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.
