Kramer Electronics, Ltd.
Contents Contents 1 2 2.1 3 3.1 3.2 3.3 4 5 6 6.1 Introduction Getting Started Quick Start Overview Shielded Twisted Pair (STP)/Unshielded Twisted Pair (UTP) About the Power Connect Feature Recommendations for Achieving the Best Performance Your TP-104/TP-104HD XGA Line Transmitter/DA Your TP-105/TP-105(HD) CAT 5 Line Driver/DA Your TP-121/TP-122 Your TP-121 XGA/Audio Line Transmitter 6.2 Your TP-122 XGA/Audio Line Receiver 10 7 7.
Contents Figure 10: TP-123 Internal Polarity Switches Figure 11: TP-124 XGA/Audio/Data Line Receiver (Topside) Figure 12: TP-124 XGA/Audio/Data Line Receiver (Underside) Figure 13: Connecting the XGA/Audio Line Transmitter/Receiver System Figure 14: CAT 5 PINOUT Figure 15: Connecting the XGA/Audio/Data Line Transmitter/Receiver System Figure 16: RS-232 PINOUT Connection Figure 17: Configuring a 1:4 XGA to Twisted Pair Transmitter/Receiver/DA Figure 18: Configuring a TP-105 CAT 5 Line Driver/DA 14 15 16 18
Introduction 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 1,000-plus different models now appear in 11 groups 1 that are clearly defined by function.
Getting Started 2.1 Quick Start This quick start chart summarizes the basic setup and operation steps.
Getting Started 3
Overview 3 Overview This user manual describes the following Kramer TOOLS: • TP-104/TP-104HD XGA Line Transmitter/DA is a line transmitter/1:4 DA that receives an XGA signal and transmits it over four CAT 5 cables to appropriate receivers (see section 4) • TP-105/TP-105(HD) CAT 5 Line Driver/DA receives a CAT 5 input 1 and distributes it to two identical outputs (see section 5) • TP-121 XGA/Audio Line Transmitter and the TP-122 XGA/Audio Line Receiver (see section 6) • TP-123 XGA/Audio/Data Line Transmitt
Overview 3.2 About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power. This feature is available when using STP cable and the distance does not exceed 50m on standard CAT 5 cable. For longer distances, heavy gauge cable should be used 1. For units which are connected via RJ-45 connectors, make sure that the shield of the STP cable is connected to the metal casing of the connectors on both ends of the cable.
Your TP-104/TP-104HD XGA Line Transmitter/DA 4 Your TP-104/TP-104HD XGA Line Transmitter/DA The TP-104/TP-104HD 1 is a line transmitter/1:4 DA that receives an XGA signal 2 and transmits it over four CAT 5 cables to appropriate receivers.
Your TP-104/TP-104HD XGA Line Transmitter/DA Table 1: TP-104, TP-104HD XGA Line Transmitter/DA Features 1 # 12V DC Feature Function 2 OUT 4 RJ-45 connector 3 OUT 3 RJ-45 connector 4 OUT 2 RJ-45 connector 5 OUT 1 RJ-45 connector 6 INPUT 15-pin HD (F) connector +12V DC connector for powering the unit Connects to 1 the LINE IN RJ-45 connector on the TP-122 XGA/Audio Line Receiver or the TP-120 XGA Line Receiver 2 Connects to1 the LINE IN RJ-45 connector on the TP-122 XGA/Audio Line Receiver or t
Your TP-105/TP-105(HD) CAT 5 Line Driver/DA 5 Your TP-105/TP-105(HD) CAT 5 Line Driver/DA The TP-105 1 receives a CAT 5 input, and distributes it to two identical outputs. In particular, the TP-105: • Has a transmission range of more than 300ft (more than 100m) over UTP cabling • Includes EQ.
Your TP-121/TP-122 6 Your TP-121/TP-122 This section defines the TP-121 XGA/Audio Line Transmitter (see section 6.1), and the TP-122 XGA/Audio Line Receiver (see section 6.2). 6.
Your TP-121/TP-122 6.1.1 The TP-121 Internal Polarity Switches Figure 6 and Table 5 define the internal sync polarity switches inside the TP-121. Note, that you need to open the TP-121 unit to gain access to the Vs and Hs Polarity switches. After setting the switches, close the TP-121 unit. NORM. NEG. Figure 6: TP-121 Internal Polarity Switches Table 5: Features of the TP-121 Internal Polarity Switches Feature VS Switch HS Switch 6.
Your TP-121/TP-122 In addition, the TP-122: • Can power or be powered by the transmitter over the same CAT 5 cable • Can change the polarity of decoding H and V Sync for video • Includes EQ. and level controls • Is 12V DC fed Figure 7 and Table 6 define the TP-122 XGA/Audio Line Receiver topside: Figure 7: TP-122 XGA/Audio Line Receiver (Topside) Table 6: TP-122 XGA/Audio Line Receiver (Topside) Features 1 2 3 4 5 6 7 8 9 # 12V DC Feature S/PDIF RCA connector ANALOG 3.
Your TP-121/TP-122 6.2.
Your TP-123/TP-124 7 Your TP-123/TP-124 This section describes the TP-123 XGA/Audio/Data Line Transmitter (see section 7.1), and the TP-124 XGA/Audio/Data Line Receiver (see section 7.2). 7.1 Your TP-123 XGA/Audio/Data Line Transmitter The TP-123 is a high-performance transmitter that accepts a computer graphics input signal, an unbalanced stereo analog audio signal, unidirectional (RxD) RS-232 control commands and 12V DC power, over CAT 5 cable, and transmits to a TP-124 receiver.
Your TP-123/TP-124 Table 8: TP-123 XGA/Audio/Data Line Transmitter Features 1 2 3 4 # 5 6 Feature 12V DC AUDIO IN 3.5mm mini jack RS-232 terminal block connector LINE OUT RJ-45 connector XGA IN 15-pin HD (F) connector ON LED Function +12V DC connector for powering the unit Connects to the audio source Connects to the PC or the Remote Controller (see section 9.1) 1 Connects to the LINE IN RJ-45 connector on the TP-124 XGA/Audio Line Receiver Connect to the XGA source Illuminates when receiving power 7.
Your TP-123/TP-124 7.2 Your TP-124 XGA/Audio/Data Line Receiver The TP-124 is a high-performance receiver obtaining the computer graphics signal/audio/control data from the Kramer TP-123 via UTP cabling at its CAT 5 Line input. The TP-124 outputs a computer graphics signal, an unbalanced stereo analog audio signal, a converted digital audio (S/PDIF) signal and RS-232 control commands.
Your TP-123/TP-124 Table 10: TP-124 XGA/Audio/Data Line Receiver (Topside) Features # 12V DC AUDIO OUT 1 2 3 Feature S/PDIF RCA connector ANALOG 3.5mm mini jack 4 5 RS-232 Terminal Block connector LINE IN RJ-45 connector 6 7 8 9 10 XGA OUT 15-pin HD (F) connector LINK LED LEVEL trimmer 3 EQ.
Connecting the XGA/Audio Line Transmitter/Receiver 8 Connecting the XGA/Audio Line Transmitter/Receiver You can use the TP-121 and TP-122 to configure an XGA/Audio Lineto-Twisted Pair Transmitter and Receiver system. To connect the TP-121 XGA/Audio Line Transmitter with the TP-122 XGA/Audio Line Receiver, as the example in Figure 13 illustrates, do the following: 1.
Connecting the XGA/Audio Line Transmitter/Receiver Figure 13: Connecting the XGA/Audio Line Transmitter/Receiver System 18 KRAMER: SIMPLE CREATIVE TECHNOLOGY
Connecting the XGA/Audio/Data Line Transmitter/Receiver 8.
Connecting the XGA/Audio/Data Line Transmitter/Receiver the TP-123 RS-232 port 1 2. On the TP-124, connect: The XGA OUT 15-pin HD (F) connector to a display The S/PDIF Audio OUT RCA connector to a digital AV Receiver (leave the ANALOG Audio OUT 3.5mm mini jack unconnected) An RS-232 cable with a 2 PIN terminal block connector at one end to the TP-124 RS-232 port1, and a 9-pin D-sub connector at the other end to the RS-232 port on an RS-232 controllable device (for example, a switcher) 3.
Connecting the XGA/Audio/Data Line Transmitter/Receiver Figure 15: Connecting the XGA/Audio/Data Line Transmitter/Receiver System 21
Connecting the XGA/Audio/Data Line Transmitter/Receiver 9.
Configuring a 1:4 XGA to TP Transmitter/Receiver/DA 10 Configuring a 1:4 XGA to TP Transmitter/Receiver/DA You can use the TP-104 XGA Line Transmitter/DA with the TP-120 XGA Line Receiver 1 to configure a 1:4 XGA-to-Twisted Pair DA system. To connect the TP-104 to four TP-120 units, as the example in Figure 17 illustrates, do the following: 1.
Configuring a 1:4 XGA to TP Transmitter/Receiver/DA Figure 17: Configuring a 1:4 XGA to Twisted Pair Transmitter/Receiver/DA 24 KRAMER: SIMPLE CREATIVE TECHNOLOGY
Configuring a TP-105 CAT 5 Line Driver/DA 11 Configuring a TP-105 CAT 5 Line Driver/DA You can connect the TP-105 CAT 5 Line Driver/DA—using a PT-110 XGA Line Transmitter and two TP-120 XGA Line Receiver 1 units—to transmit a computer graphics signal to two displays via long line CAT 5 UTP cabling. To connect the TP-105, as the example in Figure 17 illustrates, do the following: 1.
Configuring a TP-105 CAT 5 Line Driver/DA Figure 18: Configuring a TP-105 CAT 5 Line Driver/DA 26 KRAMER: SIMPLE CREATIVE TECHNOLOGY
Technical Specifications 12 Technical Specifications Table 14 includes the technical specifications of the TP-104, Table 15 includes the technical specifications of the TP-105, and Table 16 includes the technical specifications of the TP-121, TP-122, TP-123, and TP-124: 1 Table 14: Technical Specifications of the TP-104 2 and the TP-104HD INPUTS: OUTPUTS: MAX. OUTPUT LEVEL: BANDWIDTH (-3dB) 3: DIFF. GAIN3: DIFF.
Technical Specifications Table 16: Technical Specifications of the TP-121/TP-122/TP-123/TP-124 INPUTS: OUTPUTS: TP-121 VIDEO: 1 VGA/UXGA on a 15-pin HD connector AUDIO: 1 audio ANALOG 3.5mm mini jack 1 RJ-45 OUT connector MAX. OUTPUT LEVEL: CONTROLS: BANDWIDTH (-3dB) 1: S/N RATIO: TOTAL GAIN: COUPLING: TND+N: POWER SOURCE: DIMENSIONS: WEIGHT: ACCESSORIES: OPTIONS: TP-122 1 RJ-45 LINE IN connector TP-123 VIDEO: 1 VGA/UXGA on a 15-pin HD connector AUDIO: 1 audio ANALOG 3.
LIMITED WARRANTY Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product.
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing. Caution P/N: 2900- 000037 Rev: 9 Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.
