K R A ME R E LE CT R O N IC S L T D .
Contents 1 Introduction 1 2 2.1 Getting Started Achieving the Best Performance 2 2 3 3.1 3.2 4 Overview Defining EDID About the Power Connect™ Feature Defining the VS-3232DN 32x32 Digital Matrix Switcher 3 4 4 5 5 Installing in a Rack 10 6 6.1 6.2 6.3 6.4 7 7.1 7.2 7.3 7.4 7.5 7.6 8 8.1 8.
Figures Figure 1: VS-3232DN Front Panel Numeric Keypad Figure 2: VS-3232DN 32x32 Digital Matrix Switcher Front Panel Figure 3: VS-3232DN 32x32 Digital Matrix Switcher Rear Panel Figure 4: Connecting the VS-3232DN 32x32 Digital Matrix Switcher Figure 5: Sample Port Numbering Figure 6: DGKat Card Serial Data Transmission Figure 7: Local Area Connection Properties Window Figure 8: Internet Protocol (TCP/IP) Properties Window Figure 9: Default Startup Status Display Sequence Figure 10: Resolution DIP-switch Fig
1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis.
2 Getting Started We recommend that you: • Unpack the equipment carefully and save the original box and packaging materials for possible future shipment • Review the contents of this user manual • Use Kramer high performance high resolution cables • Use only the power cord that is supplied with this machine i 2.1 Go to http://www.kramerelectronics.com to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate).
3 Overview The Kramer VS-3232DN is a high performance matrix switcher chassis that supports up to 32 x 32 ports. It features a very high bandwidth of up to 3.2Gbps (for the chassis only, effective bandwidth of the system depends on the I/O cards) that ensures transparent performance even in the most critical applications. The cards re-clock and equalize the signals and the chassis can route any or all inputs to any or all outputs simultaneously.
• The Kramer 2000 Protocol for serial control • A lock function to prevent tampering with the front panel • A 40 character by 2 line LCD that shows the operational status or the configuration menu You can operate the VS-3232DN via the front panel buttons or remotely via: • RS-232 serial commands transmitted by a touch screen system, PC or other serial controller • Ethernet over a LAN • The infrared remote control transmitter The VS-3232DN is a sophisticated device but has been designed to be as
4 Defining the VS-3232DN 32x32 Digital Matrix Switcher Figure 1, Figure 2 and Figure 3 define the VS-3232DN.
6 VS-3232DN – Defining the VS-3232DN 32x32 Digital Matrix Switcher Figure 2: VS-3232DN 32x32 Digital Matrix Switcher Front Panel 6 VS-3232DN - Defining the VS-3232DN 32x32 Digital Matrix Switcher
VS-3232DN – Defining the VS-3232DN 32x32 Digital Matrix Switcher # Feature Function 1 ESC 2 EDID Press to assign EDID channels 3 STO Press to store the current setup in the a preset. After pressing the MENU button, this button lights and is enabled ALL Press to connect an input to all outputs. After pressing the MENU button, this button lights and is enabled OFF Press to turn off an output. After pressing the MENU button, this button lights and is enabled RCL Press to recall a preset.
8 VS-3232DN – Defining the VS-3232DN 32x32 Digital Matrix Switcher Figure 3: VS-3232DN 32x32 Digital Matrix Switcher Rear Panel 8 VS-3232DN - Defining the VS-3232DN 32x32 Digital Matrix Switcher
VS-3232DN – Defining the VS-3232DN 32x32 Digital Matrix Switcher Figure 3 shows DVI cards installed as an example. # 1 Feature AC Mains Power Module Function Fuse holder and power cord socket.
5 Installing in a Rack This section provides instructions for rack mounting the unit.
6 Connecting the VS-3232DN The configuration of DVI input/output cards shown in Figure 4 is a sample representation and different I/O cards may be mixed as required (for limitations, see page 12). Exactly the same principles apply to installations using other card types. i Always switch off the power to all devices before connecting them to your VS-3232DN. After connecting your VS-3232DN, connect its power and then switch on the power to each device.
To install the VS-3232DN as illustrated in the example in Figure 4: 1. Connect up to 32 DVI video sources (for example, computer graphics sources). In this example only two inputs and two outputs are connected. 2. Connect up to 32 DVI video acceptors, (for example, a plasma display and a DVI LCD display). 3. If required, connect a PC or remote controller to the RS-232 port (see Section 6.1) and/or the Ethernet port (see Section 6.4). 4. Connect the power cord.
Figure 5: Sample Port Numbering # 1 Port Number IN 1, IN 2, IN 3, IN 4 # 4 Port Number OUT 1, OUT 2, OUT 3, OUT 4 2 IN 5, IN 6 5 OUT 5, OUT 6, OUT 7, OUT 8 3 IN 9, IN 10, IN 11, IN 12 6 OUT 9, OUT 10 Note: There is no IN 7, IN 8, OUT 11 or OUT 12 because these slots contain DVI dual link cards.
6.1.1 EDID Numbering Examples The table below is based on the port numbering shown in Figure 5. Figure 8 lists EDID configuration requests and the results. 6.2 EDID Request From OUT 11 EDID Sent Blank (256 bytes of 0xFF) From IN 13 None (error message displayed) Serial Data on DGKat Plus RS-232 Cards Serial data present on the RS-232 port of a DGKat input card is not transmitted via the switcher. This data is transmitted over the TP cable of the same input card (see Figure 6).
To connect to the VS-3232DN via RS-232: • Connect the RS-232 9-pin D-sub rear panel port on the VS-3232DN unit via a 9-wire straight cable (only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5 need to be connected) to the RS-232 9-pin D-sub port on your PC 6.4 Connecting to the VS-3232DN via Ethernet You can connect the VS-3232DN via Ethernet using a crossover cable (see Section 6.4.1) for direct connection to the PC, or a straight through cable (see Section 6.4.
Figure 7: Local Area Connection Properties Window 6. Select Use the following IP Address and enter the details as shown in Figure 8. You can use any IP address in the range 192.168.1.1 to 192.168.1.255 (excluding 192.168.1.39) that is provided by your IT department.
7. Click OK. 6.4.
7 Operating Your Video Matrix Switcher This section describes: 7.1 • The startup display (see Section 7.1) • Using the selector buttons (see Section 7.2) • Confirming actions (see Section 7.3) • Switching options (see Section 7.4) • Locking the front panel (see Section 7.5) Startup Display After switching on the power, the LCD display shows the following screens in sequence.
When the unit is powered-on, the last matrix setup that was used is loaded. Use either the recall setup (see Section 8.1.6) or default setup recall (see Section 7.4.5) functions to retrieve other setups. Records a stored configuration from a preset. For quick retrieval, you can program a default setup that is commonly used. 7.1.1 Viewing the Display Figure 9 shows the output-input matrix on the LCD display. The LCD display can show 13 out of the 32 available matrix combinations at once.
The ESC button is used to cancel an operation without affecting the current status. For example, if you enter an incorrect number by mistake, press the ESC button to cancel the operation. Note: At any stage, if no button is pressed within approximately 15 seconds, the automatic timeout causes the VS-3232DN to exit the operation and revert to the output/input display. 7.3 Confirming Actions You can choose to work in the At Once (default) or the Confirm mode. For all actions except storing/recalling.
7.3.1 Toggling between the At Once and Confirm Modes To toggle between the At Once and Confirm modes: Note: If the TAKE button is flashing you cannot toggle between the At Once and Confirm modes. A flashing TAKE button indicates that an action is currently pending confirmation. 1. Press TAKE to toggle between the At Once mode and the Confirm mode. The TAKE button lights and actions now require user confirmation. 2. Press the lit TAKE button to toggle from the Confirm mode back to the At Once mode.
7.4.1 Switching one Input to one Output To switch one input to one output: 1. Using the numeric keypad, enter the required output (in this example, 12). The following is displayed: 06 07 08 09 10 11 12 13 In__ => Out 12 The left-hand side of the display shows a section of the output/input display automatically sliding the content to include output 12. 2.
2. Enter additional output-input combinations. The LCD display can show up to five pending actions (although the batch is not limited to five actions): In this example, input 9 is set to switch to output 6 and input 5 is set to switch to output 7. 09 => 06 05 => 07 3. After entering all output/input combinations, press the flashing TAKE button to confirm the actions. The inputs switch to the respective outputs as shown on the LCD display and the TAKE LED is lit. 7.4.
7.4.4 Turning Off Several Outputs To turn off several outputs in the Confirm mode, repeat the switching actions described in Section 7.4.2 but set the inputs to 00. 7.4.5 Recalling the Default Setup You can store a commonly used setup as the default setup (see Section 8.2.8) which can be recalled at any time. Note: This is not the setup that is loaded when the unit is turned on. When the unit is turned on, the setup that was last used before the unit was turned off is loaded.
To lock the front panel buttons: • Press and hold LOCK until the button lights. The front panel buttons are locked To unlock the front panel buttons: • Press and hold LOCK until the button is no longer lit. The front panel buttons are unlocked 7.6 Redundant Power Supplies The VS-3232DN supports dual, redundant power supplies. The VS-3232DN can continue to operate with only one working power supply in the event of a problem with one of the power supplies.
8 Using the Configuration Menus The configuration menus let you configure the VS-3232DN to best suit your needs. There are two configuration menus: • Setup Menu—those that are accessed on a regular basis (for example, storing setups and setting the delay), see Section 8.1 • Config Menu—those that are accessed only occasionally (for example, setting the interface or communication protocol), see Section 8.
8.1.1 Setup Menu—1: inXX=>ALL, Switching one Input to all Outputs This option switches one input to all outputs. To switch one input to all outputs: 1. Press MENU. The Setup Menu options are displayed. 2. Press 1 (ALL) on the numeric keypad (see Figure 1). The following is displayed: in__ => ALL 3. Using the numeric keys, enter the input to be switched to all outputs. The TAKE button flashes. 4. Press TAKE. The selected input is switched to all outputs.
The display reverts to the output/input display showing that the selected output is turned off with the input being blank. 8.1.3 Setup Menu—7: EDID, Assignment to an Input This option assigns an EDID to between one and eight inputs which are stored in non-volatile memory. More than eight EDID assignments must be assigned in separate batches of eight. Each input on the VS-3232DN has a factory default EDID loaded (see Section 15).
6. Press TAKE. The EDID is stored and passed through to the input. The display reverts to the output/input display. 7. Repeat the above steps for the next batch of eight EDID assignments. To view the EDID assignments: 1. Press MENU. The Setup Menu options are displayed. 2. Press 7 (EDID) on the numeric keypad (see Figure 1). The following is displayed: SETUP EDID ENTER to View EDID and Set EDID 3. Press ENT. The current EDID matrix configuration is displayed.
3. Using the numeric keys, enter the output (in this example, 03). The following is displayed: 01 02 03 04 05 06 07 08 DLY__ =>out03 4. Using the numeric keys, enter the number of delay units. 5. Press TAKE. The selected output delay is set. The display reverts to the output/input display. 8.1.5 Setup Menu—4: store setup XX, Storing the Setup in a Preset This option stores the current setup in a preset (1 to 59). To store the current setup in a preset: 1. Press MENU. The Setup Menu options are displayed.
8.1.6 Setup Menu—6: recall setup XX, Recalling a Preset This option recalls a stored configuration from a preset (1 to 59). To recall a stored configuration: 1. Press MENU. The Setup Menu options are displayed. 2. Press 6 (RCL) on the numeric keypad (see Figure 1). The following is displayed: recall <= __ 3. Using the numeric keys, enter the preset (in this example, 02) to recall. The following is displayed: Wait …..
• Protocol configuration (Section 8.2.7) • Storing the default setup (Section 8.2.8) • Resetting the VS-3232DN (Section 8.2.9) • Firmware revision display (Section 8.2.10) To enter the Config Menu press MENU twice. The MENU button lights and the following message is displayed: • Start configuration menu • MENU to view setups ENT to change them When browsing through the configuration menu, enabled buttons light or flash. Use the Config Menu as follows: 1.
To display a list of inputs that have detected signals: 1. Press MENU twice. The following message is displayed: start configuration menu MENU to view setup ENT to change them 2. Press MENU. The following is displayed: IN: 01 02 03 04 05 06 07 08 09 10 11 SIG: Y X Y Y Y Y X Y Y Y X Y indicates that a signal is detected and X indicates that no signal is detected on the relevant input. 3. Do one of the following: 8.2.
X indicates that there are no modifiable parameters for the associated port and 0 indicates that there are modifiable parameters for the associated port. 3. Press TAKE to enter the list of ports. The cursor flashes on a selected port. 4. Select the required port to modify using the left and right arrow buttons. 5. Press TAKE to enter the parameters list. A message similar to the following is displayed with the relevant port number in place of 06: IN: 06 SET: 36.Reset SubBoard 6.
HDMI plus Analog Audio Input Card Parameter 84.Audio Balance Options/Description 0 to 100: sets the audio input channel balance Default 50 87.Audio Bass 0 to 100: sets the audio inout bass level 50 88.Audio Treble 0 to 100: sets the audio input treble level 50 91.Audio Mute MUTE: mutes the audio input Non-MUTE: unmutes the audio input Non-MUTE 98.Audio Select Auto: audio signal selection is controlled by the presence or absence of a plug in the 3.
3. Do one of the following: 8.2.4 Press BREAKAWAY to exit the Config Menu Wait approximately 15 seconds for the operation to time out Press MENU to move to the next Config Menu option Config Menu—Output Port Parameter Setting This option sets port specific parameters. Ports that show an X have no parameters available to modify. Ports that show a 0 have parameters available to modify.
6. To select the next parameter press the right arrow button. (See the table at the end of this section for available parameters.) Or: 7. To enter the displayed parameter press TAKE. The parameter options are displayed. 8. Select the required action or number using the keypad numbers and arrows. 9. Press TAKE to save the change. 10. Repeat from Step 6 to modify other parameters 11.
HDMI plus S/PDIF Audio Output Card Parameter 36.Reset SubBoard Options/Description Re-power: power cycles the port Factory: performs a factory reset to default values of the port Default Re-power 151.BLINK ON AUDIO 1: No video glitch when the audio is connected or disconnected 0: There is a video glitch when the audio is connected or disconnected 1 8.2.5 Config Menu—Interface Configuration This option lets you activate or deactivate the IR (infrared) and Ethernet interfaces.
8.2.6 Config Menu—Interface Reply Configuration This option lets you switch the Reply configuration on or off. Setting Reply to on causes all interfaces that are set to on to accept and execute commands, and also to reply. Setting Reply to off causes all interfaces that are set to on to accept and execute commands, but not to reply. To switch the Reply configuration on or off: 1. Press MENU twice. The following message is displayed: start configuration menu MENU to view setup ENT to change them 2.
2. Press MENU until the following is displayed: PROTOCOL configuration Current: Kramer-3000 This indicates the current Protocol setting. 3. Press ENT to enter the Reply Submenu. The following is displayed: PROTOCOL configuration 1:KRAMER-2000 2:KRAMER-3000 4. Press 1 to switch to Protocol 2000. The following is displayed: Set PROTOCOL to KRAMER-2000? press TAKE to confirm 5. Press TAKE to confirm the action. A message is displayed indicating the new Protocol status.
3. Press ENT to store the current configuration as the default configuration. The following is displayed: current matrix stage is OKAY? press TAKE to confirm 4. Press TAKE. The following is displayed: current matrix stage store as DEFAULT setup This indicates that the current setup is stored as the default setup. After a few seconds the next option on the Config Menu is displayed. 8.2.
5. Press TAKE and wait a few seconds. The following is displayed: Are you Absolutely sure !!! Once more TAKE to confirm 6. Press TAKE. The following is displayed: Matrix erased!!! Please, wait … The matrix and device configuration are erased. After a few seconds the next option on the Config Menu is displayed. 8.2.10 Config Menu—Display Firmware Versions This option displays the main and front firmware versions. To display the firmware versions: 1. Press MENU twice.
9 Configuring the Number of Installed Input and Output Ports After installing or removing a module you need to set the number of input and output ports so that the VS-3232DN recognizes the new configuration. Refer to Section 6.1 for an explanation of port numbering before setting the number of input and output ports. To set the number of input or output ports: 1. Press ESC, ENT and LOCK together. The following is displayed: Configuration Device 2. Press ENT.
10 Installing and Using the Test Module to Troubleshoot Video Problems The VS-3232DN includes a test module which acts as a signal generator and can be used to diagnose video/audio issues in an operating environment. The test module must be installed in the configuration before it can be used. When installing the test module, the number of configured inputs and outputs must be increased by one.
10.2 Setting the Resolution of the Generated Video The test module generates a range of both PC and HD resolutions which are selected by a combination of DIP-switches and an on-board jumper (labeled B3). Install the jumper to select HD resolutions or remove the jumper to select PC resolutions. The Resolution DIP-switch is used to set the resolution of the generated video as listed in the tables below.
10.3 Setting the Pattern of the Generated Video The Pattern button is used to set the pattern of generated video. There are 32 available patterns. Press the button repeatedly to cycle through the patterns. 10.4 Using the Test Module to Troubleshoot Video Problems The test module may be used in various ways to isolate video problems.
10.4.1 Testing the Projector Output Signal path: c to d; d to projector To test the projector output: 1. Configure Input 33 to Output 33 (see Section 7.4). 2. Connect Output 33 to the projector. 3. Set the generated video resolution (see Section 10.2). 4. Set the pattern for the generated video (see Section 10.3). 5. Verify that the projector output is as expected. 10.4.
4. Connect Output 1 to the projector. 5. Set the generated video resolution (see Section 10.2). 6. Set the pattern for the generated video (see Section 10.3). 7. Verify that the projector output is as expected.
11 Hardware Installation Instructions 11.1 I/O Card Installation The VS-3232DN I/O cards mount in one of the 16 slots on the rear of the VS-3232DN chassis. Slots are numbered from left to right and must be filled consecutively from left to right, without leaving empty slots. WARNING: An input card must only be mounted in a slot designated for input cards (slots IN 1 to 16 and IN 17 to 32) and an output card must only be mounted in a slot designated for output cards (slots OUT 1 to 16 and OUT 17 to 32).
To install an I/O card as shown in Figure 12: 1. Power off the VS-3232DN and all devices connected to it. 2. Using a Phillips screwdriver, loosen the screws at the top and bottom of the blanking plate. 3. Remove the blanking plate from the slot and store it for possible future use. 4. Remove the new card from its shipping box and anti-ESD bag. 5. Holding the card by the upper and lower handle, align the card with the plastic guide rails (see Figure 13). Figure 13: Card Handles 6.
9. Power on the VS-3232DN and follow the procedure to configure the new card (see Section 9). 10. Power on the peripheral devices. 11.2 Power Supply Installation The VS-3232DN is supplied with a single power supply. You can install a second power supply to provide redundancy. Figure 14: Second Power Supply Installation To install a second power supply as shown in Figure 12: 1. Remove the new power supply from its shipping carton and anti-static bag. 2. Power down the chassis. 3.
6. Press the power supply firmly until the front panel of the power supply is flush with the front panel of the VS-3232DN. 7. Tighten the four thumbscrews to secure the power supply in place. 8. Power on the chassis.
12 Upgrading the VS-3232DN Firmware Upgrading the firmware on the VS-3232DN can be done only by authorized service personnel.
13 Technical Specifications BANDWIDTH: Supports up to 3.2Gbps bandwidth per channel (limited by the cards installed) MAX RESOLUTION: Up to UXGA; 1080p CONTROLS: Front panel buttons, Infrared remote control transmitter, RS-232, Ethernet OPERATING TEMPERATURE: 0° to +55°C (32° to 131°F) STORAGE TEMPERATURE: –45° to +72°C (–49° to 162°F) HUMIDITY: 10% to 90%, RHL non-condensing DIMENSIONS: 19” x 14.2” x 6U (W, D, H) rack-mountable POWER CONSUMPTION: 100-240V AC, 50/60Hz, 320VA WEIGHT: 13.
14 Default Communication Parameters The following table lists the default communication parameters for the VS-3232DN. EDID EDID data is passed between Output 1 and Input 1 RS-232 Protocol 2000 Baud Rate 9600 Data Bits 8 Stop Bits 1 Parity None Command Format HEX Example (To switch Output 1 to Input 1) 0x01, 0x81, 0x81, 0x81 Ethernet IP Address 192.168.1.
15 15.1 Factory Default EDID DVI Input Card Monitor Model name............... VS-32DVI Manufacturer............. KRM Plug and Play ID......... KRM0200 Serial number............ 1 Manufacture date......... 2006, ISO week 12 Filter driver............ None ------------------------EDID revision............ 1.3 Input signal type........ Digital (DVI) Color bit depth.......... Undefined Display type............. RGB color Screen size.............. 700 x 390 mm (31.5 in) Power management.........
1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,0C,10,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,8B,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,64,19,00,40,41,00,26,30,18,88, 36,00,6F,13,11,00,00,1E,28,3C,80,A0,70,B0,23,40,30,20,36,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,33,32,44,56,49,0A,20,20,20,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,00,85 15.2 DVI (HDCP) Input Card Monitor Model name.....
1440 x 900p at 60Hz - VESA STD 1280 x 960p at 60Hz - VESA STD 1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number.......... 3 IT underscan............. Not supported Basic audio.............. Supported YCbCr 4:4:4.............. Supported YCbCr 4:2:2.............. Supported Native formats........... 1 Detailed timing #1....... 720x480p at 60Hz (4:3) Modeline............... "720x480" 27.
Manufacture date......... 2006, ISO week 12 Filter driver............ None ------------------------EDID revision............ 1.3 Input signal type........ Digital (DVI) Color bit depth.......... Undefined Display type............. RGB color Screen size.............. 700 x 390 mm (31.5 in) Power management......... Not supported Extension blocs.......... 1 (CEA-EXT) ------------------------DDC/CI................... n/a Color characteristics Default color space...... Non-sRGB Display gamma............ 2.
Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync Detailed timing #3....... 1920x1080i at 50Hz (16:9) Modeline............... "1920x1080" 74.250 1920 2448 2492 2640 1080 1084 1094 1124 interlace +hsync +vsync Detailed timing #4....... 1280x720p at 60Hz (16:9) Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync Detailed timing #5....... 1280x720p at 50Hz (16:9) Modeline............... "1280x720" 74.
Green chromaticity....... Gx 0.286 - Gy 0.610 Blue chromaticity........ Bx 0.146 - By 0.069 White point (default).... Wx 0.284 - Wy 0.293 Additional descriptors... None Timing characteristics Horizontal scan range.... 31-94kHz Vertical scan range...... 50-85Hz Video bandwidth.......... 170MHz CVT standard............. Not supported GTF standard............. Not supported Additional descriptors... None Preferred timing......... Yes Native/preferred timing.. 1024x768p at 60Hz (4:3) Modeline...............
CE audio data (formats supported) LPCM 3-channel, 24-bits at 44/48 kHz CE speaker allocation data Channel configuration.... 3.0 Front left/right......... Yes Front LFE................ No Front center............. Yes Rear left/right.......... No Rear center.............. No Front left/right center.. No Rear left/right center... No Rear LFE................. No CE vendor specific data (VSDB) IEEE registration number. 0x000C03 CEC physical address..... 1.0.0.0 Maximum TMDS clock.......
Standard timings supported 720 x 400p at 70Hz - IBM VGA 720 x 400p at 88Hz - IBM XGA2 640 x 480p at 60Hz - IBM VGA 640 x 480p at 67Hz - Apple Mac II 640 x 480p at 72Hz - VESA 640 x 480p at 75Hz - VESA 800 x 600p at 56Hz - VESA 800 x 600p at 60Hz - VESA 800 x 600p at 72Hz - VESA 800 x 600p at 75Hz - VESA 832 x 624p at 75Hz - Apple Mac II 1024 x 768i at 87Hz - IBM 1024 x 768p at 60Hz - VESA 1024 x 768p at 70Hz - VESA 1024 x 768p at 75Hz - VESA 1280 x 1024p at 75Hz - VESA 1152 x 870p at 75Hz - Apple Mac II 128
Maximum TMDS clock.......
1152 x 870p at 75Hz - Apple Mac II 1280 x 720p at 60Hz - VESA STD 1280 x 800p at 60Hz - VESA STD 1440 x 900p at 60Hz - VESA STD 1280 x 960p at 60Hz - VESA STD 1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number.......... 3 IT underscan............. Not supported Basic audio.............. Supported YCbCr 4:4:4.............. Supported YCbCr 4:2:2.............. Supported Native formats...........
16 Communication Protocols 16.1 Protocol 3000 The VS-3232DN can be operated using serial commands from a PC, remote controller or touch screen using the Kramer Protocol 3000. This section describes the: 16.1.1 • Kramer Protocol 3000 syntax (see Section 16.1.1) • Kramer Protocol 3000 commands (see Section 16.1.8) Kramer Protocol 3000 Syntax 16.1.1.1 Host Message Format Start Address (optional) Body Delimiter # device_id@ Message CR 16.1.1.
LF = Line feed (ASCII 10 = 0x0A) SP = Space (ASCII 32 = 0x20) 16.1.3 Command Terms Command A sequence of ASCII letters ('A'-'Z', 'a'-'z' and '-'). Command and parameters must be separated by at least one space. Parameters A sequence of alphanumeric ASCII characters ('0'-'9','A'-'Z','a'-'z' and some special characters for specific commands). Parameters are separated by commas.
16.1.4 Entering Commands You can directly enter all commands using a terminal with ASCII communications software, such as HyperTerminal, Hercules, etc. Connect the terminal to the serial or Ethernet port on the Kramer device. To enter CR press the Enter key. ( LF is also sent but is ignored by command parser). For commands sent from some non-Kramer controllers like Crestron, some characters require special coding (such as, /X##). Refer to the controller manual. 16.1.
16.1.
16.2 Protocol 2000 Tables of HEX Codes for Serial Communication (Protocol 2000) The following table lists the Protocol 2000 hex codes for switching inputs 1 to 32 to outputs 1 to 16. Full details are available on our Web site at http://www.kramerelectronics.
IN 14 IN 15 IN 16 IN 17 IN 18 IN 19 IN 20 IN 21 IN 22 IN 23 IN 24 IN 25 IN 26 IN 27 IN 28 IN 29 IN 30 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 OUT 9 OUT 10 OUT 11 OUT 12 OUT 13 OUT 14 OUT 15 01 8E 81 81 01 8F 81 81 01 90 81 81 01 91 81 81 01 92 81 81 01 93 81 81 01 94 81 81 01 95 81 81 01 96 81 81 01 97 81 81 01 98 81 81 01 99 81 81 01 9A 81 81 01 9B 81 81 01 9C 81 81 01 9D 81 81 01 9E 81 81 01 8E 82 81 01 8F 82 81 01 90 82 81 01 91 82 81 01 92 82 81 01 93 82 81 01 94
IN 31 IN 32 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 OUT 9 OUT 10 OUT 11 OUT 12 OUT 13 OUT 14 OUT 15 01 9F 81 81 01 A0 81 81 01 9F 82 81 01 A0 82 81 01 9F 83 81 01 A0 83 81 01 9F 84 81 01 A0 84 81 01 9F 85 81 01 A0 85 81 01 9F 86 81 01 A0 86 81 01 9F 87 81 01 A0 87 81 01 9F 88 81 01 A0 88 81 01 9F 89 81 01 A0 89 81 01 9F 8A 81 01 A0 8A 81 01 9F 8B 81 01 A0 8B 81 01 9F 8C 81 01 A0 8C 81 01 9F 8D 81 01 A0 8D 81 01 9F 8E 81 01 A0 8E 81 01 9F 8F 81 01 A0 8F 81 OUT 16 01 9F
IN 13 IN 14 IN 15 IN 16 IN 17 IN 18 IN 19 IN 20 IN 21 IN 22 IN 23 IN 24 IN 25 IN 26 IN 27 IN 28 IN 29 OUT 17 OUT 18 OUT 19 OUT 20 OUT 21 OUT 22 OUT 23 OUT 24 OUT 25 OUT 26 OUT 27 OUT 28 OUT 29 OUT 30 OUT 31 01 8D 91 81 01 8E 91 81 01 8F 91 81 01 90 91 81 01 91 91 81 01 92 91 81 01 93 91 81 01 94 91 81 01 95 91 81 01 96 91 81 01 97 91 81 01 98 91 81 01 99 91 81 01 9A 91 81 01 9B 91 81 01 9C 91 81 01 9D 91 81 01 8D 92 81 01 8E 92 81 01 8F 92 81 01 90 92 81 01 91 92 81 01 92 92
IN 30 IN 31 IN 32 74 OUT 17 OUT 18 OUT 19 OUT 20 OUT 21 OUT 22 OUT 23 OUT 24 OUT 25 OUT 26 OUT 27 OUT 28 OUT 29 OUT 30 OUT 31 01 9E 91 81 01 9F 91 81 01 A0 91 81 01 9E 92 81 01 9F 92 81 01 A0 92 81 01 9E 93 81 01 9F 93 81 01 A0 93 81 01 9E 94 81 01 9F 94 81 01 A0 94 81 01 9E 95 81 01 9F 95 81 01 A0 95 81 01 9E 96 81 01 9F 96 81 01 A0 96 81 01 9E 97 81 01 9F 97 81 01 A0 97 81 01 9E 98 81 01 9F 98 81 01 A0 98 81 01 9E 99 81 01 9F 99 81 01 A0 99 81 01 9E 9A 81 01 9F 9A 81 01 A0 9A 8
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. Web site: www.kramerelectronics.com E-mail: info@kramerel.
