K R A ME R E LE CT R O N IC S L TD .
Contents 1 Introduction 1 2 2.1 2.2 2.3 3 3.1 3.2 3.3 4 4.
1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis.
2 Getting Started We recommend that you: Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual i 2.1 Go to http://www.kramerelectronics.com to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate).
2.2 Safety Instructions ! 2.3 Caution: There are no operator serviceable parts inside the unit Warning: Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning: Disconnect the power and unplug the unit from the wall before installing Recycling Kramer Products The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled.
3 Overview The TP-202 is a twisted pair branching receiver for computer graphics video signals with resolutions from VGA up to UXGA and higher or HDTV signals. It takes a twisted pair signal and converts it into a computer graphics video signal or HDTV signal available on two 15-pin HD outputs, and simultaneously re-transmits the original twisted pair signal to another compatible receiver.
3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) We recommend that you use Shielded Twisted Pair (STP) cable, and stress that the compliance to electromagnetic interference was tested using STP cable. There are different levels of STP cable available, and we advise you to use the best quality STP cable that you can afford. Our non-skew-free cable, Kramer BC-STP is intended for analog signals where skewing is not an issue.
# 1 Feature Function EQ.
4 Connecting the TP-202 i Always switch off the power to each device before connecting it to your TP-202. After connecting your TP-202, connect its power and then switch on the power to each device. You can use the TP-202 UXGA Line Transceiver/DA to configure a UXGA DA system. This lets you transmit a computer graphics signal to two displays via long line CAT 5 UTP cabling. By using two TP-202 units, you can transmit the signal to an additional TP-202.
TP-202, decoded and converted at the UXGA OUT 1 and UXGA OUT 2 15-pin HD connectors to the UXGA acceptors simultaneously. ! When chaining several units, we recommend using an STP cable between the transmitter and the receiver and a skew-free cable for connecting the TP-202 units. When using the TP-202 as a standalone, we recommend using UTP cables.
4.1 Wiring the TP LINE IN / LINE OUT RJ-45 Connectors This section defines the TP pinout, using a straight pin-to-pin cable with RJ-45 connectors. i Note, that the cable Ground shielding must be connected / soldered to the connector shield.
5 Technical Specifications INPUT: 1 CAT 5 LINE IN on an RJ-45 connector OUTPUTS: 1 CAT 5 LINE OUT on an RJ-45 connector 2 UXGA on 15-pin HD connectors MAX. OUTPUT LEVEL: 1.5Vpp RESOLUTION: Up to UXGA, up to 1080p DIFF. GAIN: 2.8% DIFF. PHASE: 0.2Deg K-FACTOR: 0.1% S/N RATIO: 69.2dB @5MHz CONTROLS: Level: -9.6dB to +2.3dB; Equalization: 0dB to 36.
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. Web site: www.kramerelectronics.com E-mail: info@kramerel.
