K R A ME R E LE CT R O N IC S L TD .
Contents 1 Introduction 1 2 2.1 2.2 2.3 2.4 2.5 Getting Started Achieving the Best Performance Safety Instructions Recycling Kramer Products About the Power Connect™ Feature Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) 2 2 2 3 3 3 3 3.1 3.2 3.3 3.4 4 4.1 4.2 4.3 5 5.1 5.
1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis.
2 Getting Started We recommend that you: Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual i 2.1 Go to http://www.kramerelectronics.com/support/product_downloads.asp to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate).
2.3 Recycling Kramer Products The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled. To comply with the WEEE Directive, Kramer Electronics has made arrangements with the European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility.
3 PT-110xl UXGA Line Transmitter The Kramer Pico TOOLS PT-110xl is an extended range UXGA line transmitter that receives a UXGA signal and transmits it over a CAT 5/6 cable to the PT-120xl or TP-120 receiver.
3.2 Connecting the PT-110xl UXGA Line Transmitter To connect the PT-110xl (as shown in Figure 2) do the following: 1. Connect a UXGA source (for example, a computer graphics card) to the 15-pin HD UXGA INPUT connector. 2. Connect a CAT5/6 cable to the RJ-45 LINE OUT connector. 3. On both the PT-110xl and the TP line receiver, connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity.
3.3 Capturing the EDID To capture an EDID: Connect the device from which you want to capture the EDID (for example, a display, switcher, DA, etc.) directly to the UXGA input of the PT-110xl Press the EDID capture button. The EDID status LED flashes slowly several times. The new EDID is captured when the LED stops flashing and lights solid. Note: If the status LED flashes quickly for a few seconds and then stays on solid, the PT-110xl could not capture the EDID and loaded the default EDID instead.
4 WP-110 XGA Line Transmitter The Kramer Wall Plate WP-110 is an XGA line transmitter that receives an XGA signal and transmits it over a CAT 5 cable to the PT-120xl or TP-120 receiver. The WP-110 is available in three versions: one for USA, one for Belgium and Germany, and one for UK and most of Europe (excluding Belgium and Germany). In particular, the WP-110 features: Resolution of up to XGA Use of the simplest UTP CAT 5 cables, however, it benefits from better quality cables 4.
Figure 3: WP-110 XGA Line Transmitter # 1 Feature ON LED Function Illuminates when receiving power 2 XGA IN 15-pin HD (F) Connector Connect to the XGA source 3 POWER SUPPLY 4 GND PIN Connect (-) to the Ground +12V DC PIN Connect (+) to the connector for powering the unit LINE OUT RJ-45 Connector Connects to the LINE IN RJ-45 connector on the PT-120xl or TP-120 XGA Line Receiver Use a UTP cable with CAT 5 connectors at both ends (the PINOUT is defined in Figure 8) 8 5 HS Switch Slide the sw
4.2 Installing the WP-110 XGA Line Transmitter To install your WP-110 XGA Line Transmitter: 1. Connect the LINE OUT RJ-45 connector to the pre-installed UTP wiring in the wall box opening that connects via UTP cabling to the LINE IN RJ-45 connector of the PT-120xl or TP-120. 2. Connect your 12V DC power supply to the POWER SUPPLY pins, taking care that polarity is correct. Connect the wire labeled “+” to the +12V pin, and the wire labeled “–” to the GND pin. 3.
6. If necessary, set the H SYNC and V SYNC switches, on the underside of the WP-110. By default, both switches are set for normal H SYNC and V SYNC polarity.
5 PT-120xl XGA Line Receiver The Kramer Pico TOOLS PT-120xl is an XGA line receiver that receives a coded CAT 5 signal transmitted by the WP-110, decodes it and converts it to an XGA output. In particular, the PT-120xl features: An operating range of up to 300m using standard CAT 5 cable and the PT-110xl 5.1 EQ.
5.2 Connecting the PT-120xl XGA Line Receiver To connect the PT-110xl XGA Line Transmitter to the PT-120xl XGA Line Receiver, as the example in Figure 4 illustrates, do the following: 1. On the PT-110xl, connect the XGA source (for example, the 15-pin HD output from a computer’s graphics card) to the XGA INPUT 15-pin HD (F) connector. 2. On the PT-120xl, connect the XGA OUT 15-pin HD (F) connector to the XGA acceptor (for example, a monitor). 3.
6 TP-120 XGA Line Receiver The Kramer TOOLS TP-120 is an XGA line receiver that receives a coded CAT 5 signal transmitted by the WP-110, decodes it and converts it to an XGA output. In particular, the TP-120 features: An operating range of more than 300ft (more than 100m) using standard CAT 5 cable and the WP-110 6.1 EQ.
6.3 Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors This section defines the CAT 5 pinout, using a straight pin-to-pin cable with RJ-45 connectors. i Note, that the cable ground shielding must be connected / soldered to the connector shield.
7 Technical Specifications WP-110 PT-110xl PT-120xl TP-120 INPUTS: 1 VGA/UXGA on a 15-pin HD connector 1 VGA / UXGA on a 15-pin HD connector 1 RJ-45 LINE IN connector 1 RJ-45 LINE IN connector OUTPUTS: 1 RJ-45 LINE OUT connector 1 RJ-45 LINE OUTPUT connector 1 VGA / UXGA on a 15-pin HD connector 1 VGA / UXGA on a 15-pin HD connector 1.3Vpp 1.4Vpp Up to WUXGA, 1080p Up to WUXGA, 1080p Up to UXGA Up to 250m (820ft) Up to 300m (990ft) More than 100m (330ft) Level: 0.7v to 1.
16 PT-110xl, WP-110, PT-120xl, TP-120 - Technical Specifications
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. Web site: www.kramerelectronics.com E-mail: info@kramerel.
