USER MANUAL MODEL: VS-211H2 Automatic HDMI Standby Switcher P/N: 2900-300581 Rev 4 www.kramerAV.
Kramer Electronics Ltd.
Kramer Electronics Ltd. Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis.
Kramer Electronics Ltd. Recycling Kramer Products The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled.
Kramer Electronics Ltd. Overview Congratulations on purchasing your Kramer VS-211H2 Automatic HDMI Standby Switcher. This product, which incorporates HDMI™ technology, is ideal for Presentation systems in conference rooms, boardrooms, auditoriums, hotels and churches, production studios, rental and staging. The VS−211H2 is a high−performance automatic switcher for HDMI video signals.
Kramer Electronics Ltd. Defining VS-211H2 Automatic HDMI Standby Switcher This section defines VS-211H2.
Kramer Electronics Ltd. Connecting VS-211H2 Always switch off the power to each device before connecting it to your VS-211H2. After connecting your VS-211H2, connect its power and then switch on the power to each device. To connect VS-211H2, as illustrated in the example in Figure 2, do the following: 1. Connect the INPUT 1 connector to HDMI source 1 (for example, a Blu-ray player). 2. Connect the INPUT 2 connector to HDMI source 2 (for example, a laptop computer graphics source 4K@60 UHD). 3.
Kramer Electronics Ltd. Connecting REMOTE Terminal Block Connector Regardless of the default input switch setting, you can force the switching of the active input by remote control. To do this, connect the appropriate REMOTE input terminal block connector pins to a momentary contact closure switches (pushbuttons) (see Figure 3). • To force input source 1: momentarily connect REMOTE IN1 to PIN G (ground). • To force input source 2: momentarily connect REMOTE IN2 to PIN G (ground).
Kramer Electronics Ltd. Priority Setting: DIP 1 is Set to ON (Down) In this switching mode, if a source is present on the “priority input”, then this source is switched to the output. DIP 2 defines the priority input: • When set to OFF (up), INPUT 1 is the priority input. • When set to ON (down), INPUT 2 is the priority input. Reactivating or reconnecting the non-priority input has no effect on switching.
Kramer Electronics Ltd. Technical Specifications Inputs Outputs Ports 2 HDMI 1 HDMI 2 Contact-Closure Switches On a female HDMI connector On a female HDMI connector On a 3–pin terminal block connector for remote device operation Video Max. Data Rate 17.82GBPS (5.94Gbps per graphic channel) Max Resolution 4K@60 UHD (4:4:4) Compliance HDR10, HDCP 2.2 (does not support conversion to HDCP 1.4) HDMI Support Deep color, x.v.Color™, Lip Sync, up to 7.1 Uncompressed Audio Channels, CEC as specified in HDMI 2.0.
The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below: What is Covered This limited warranty covers defects in materials and workmanship in this product.
P/N: 2900- 300581 Rev: 4 SAFETY WARNING Disconnect the unit from the power supply before opening and servicing For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. www.KramerAV.com info@KramerAV.
