R INSTALLATION MANUAL All-in-One Filtration Set FS-1000 / FS-1000-B www.kraususa.com I Toll Free: 1.800.775.0703 I © 2024 Kraus USA Plumbing LLC I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Installation and use must comply with all state and local laws, regulations and codes. STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Observe all state and local plumbing and building codes.
Tools Required Adjustable Wrench Utility Knife Drill Tape Measure Permanent Marker Safety Goggles Cut Resistant Gloves Care & Maintenance * To keep the product clean & shining, follow the steps below: 1. 2. Rinse with clean water & dry with a soft cloth. Do not clean with soaps, acid, polish, abrasives or harsh cleaners as use of such products may affect product performance or void the warranty. Do not use cloth with a coarse surface. 3.
Diagram and Parts List 1. Tee Adapter 2. Manifold 3. Polypropylene Cartridge 4. Compressed Carbon Cartridge 5. Quick Connect Lock Tab 6. Mounting Screw & Anchor x 3 7. Tubing 1/4" x 8' 8. 3x AA Batteries 9.
Dimensions and Specifications 4 7/8" (125mm) 15 1/2" (394mm) 9 1/2" (240mm) Flow Rate 0.7GPM Capacity: 700 gallons NOTE: Depending on local water quality and use environment, the actual filtered water flow rate and total filtered water volume will vary. Min static pressure: 40 psi (275.8 kPa) Max static pressure: 120 psi (827.
Step 1. Tee Adapter 3/8" Cold Water Supply Turn off the cold water supply and turn on the faucet to relieve the water pressure and drain water from the water line. Disconnect the cold water supply line from the cold water supply valve. Install the tee adapter to the cold water supply valve. NOTE: Make sure to check for washer in the Tee Adapter before connecting to the angle stop.
Step 2. Fasteners Cabinet Wall Screws Cabinet Top Cabinet Wall Position drill holes as indicated 7.87"(200mm) wall wall Cabinet Base MOUNTING TEMPLATE 8 Cabinet Wall Using the mounting template, mount the manifold. Align the mounting holes of the manifold at the proper mounting location. Mark the hole locations with a permanent marker. Place the manifold aside and pre-drill the mounting holes, if necessary, depending on the fasteners selected.
Step 3. Insert the batteries into the battery compartment by lifting up the tabs. Drill a 1/4" hole in the wall a few inches away from your filtration system. Place the anchor inside the hole and then fasten the battery compartment to the wall by screwing it into the anchor. You can also use the tape on the back to install it to the wall. ! CAUTION - To avoid the risk of personal injury, wear safety glasses and cut resistant gloves with non-slip grip when drilling.
Step 4. Connect the tubing. Wet one end of the tubing sections with water and press it firmly into the inlet port of the filter head. Wet the other end of the tubing and press it firmly into the tee adapter. Repeat for the other end of tubing, pressing one end into the outlet port of the filter head and the other end into the filtered water faucet supply. IMPORTANT: Use the quick connect lock tabs to prevent any accidental tube release.
Step 5. Cap O-rings Install the filter cartridges. Write the date on the new filter cartridge label. Remove the cap from the filter cartridge and discard. Inspect the cartridge for any damage. Make sure both sets of O-rings are present and are positioned correctly. Align the filter cartridge as shown and press upward into the filter head. Rotate the filter cartridge counterclockwise 90° until it is secure in the filter head. Repeat for the second cartridge.
Step 7. Display & Reset: After installing new filters push and hold the settings button for 3 seconds. Filter 1 icon will blink. Push the reset button and hold for 3 seconds and the icon will reset to full capacity. Push the settings button again and filter 2 icon will blink. Push and hold the reset button for 3 seconds and the icon will reset to full capacity. Push the settings button to exit the reset mode.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Water leaks between the filter head and the filter cartridge. An O-ring is damaged, dirty, or out of place. Turn off the water supply, and relieve water pressure. Remove the filter cartridge and inspect the O-rings for damage or debris, and ensure that the O-rings are in place.
Replacement Parts Replacement Parts List 1 2 3 Part # 1. Quick Connect Lock Tab KP26063 DMT 2. Mounting Screws & Anchors KP26061 Keruichuang & Shengfa 3. Tubing 1/4" x 8' KP26062 Zhongdenuo 4. Tee Adapter KP26064 KF-1CB Filtertech 6. Polypropylene Cartridge KF-1PP Filtertech 8. Battery Compartment 5 Meigu 5. Compressed Carbon Cartridge 7.
Performance Data Sheet (based on VOC surrogate testing) Substance Influent Challenge Concentration mg/L Minimum % Reduction or Maximum Product Water Concentration Requirement mg/L alachlor 0.050 0.001 atrazine 0.100 0.003 benzene 0.081 0.001 carbofuran 0.190 0.001 carbon tetrachloride 0.078 0.0018 chlorobenzene 0.077 0.001 chloropicrin 0.015 0.0002 2,4-D 0.110 0.0017 dibromochloropropane (DBCP) 0.052 0.00002 o-dichlorobenzene 0.080 0.001 p-dichlorobenzene 0.040 0.
Codes/Standards Applicable: UP C R The system is certified by IAPMO R&T according to NSF/ANSI 42 standard for material safety, structural integrity, chlorine, particulate I; NSF/ANSI 53 standard for Lead, VOC and PFOA/PFOS reduction; NSF/ANSI 401 standard for Bisphenol A, Phenytoin, Ibuprofen, Naproxen, Estrone, Nonylphenol and NSF/ANSI 372 for low lead compliance. See Performance Data Sheet for individual contaminants and reduction performance.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC R 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
