I N S TA L L AT I O N MA N UA L Coda 8” Widespread Basin Faucet FUS-13803 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
7/8” (22mm) 19.7º 10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) ∅ 1 3/4” Prior (∅ 45mm) ∅ 1 15/16” • (∅ 50mm) 1 3/8” (35mm) to Installation: Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-7750703 for a replacement • Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
FUS-13803 Diagram and Parts List A B O1 O2 O3 C D G E F H I N J K 3 M L
A. Hot & Cold Handle B. Base Metal Ring C. Base O-Ring (factory-installed in base metal ring) D. Rubber Washer E. Mounting Nut F. Hot Valve G. Spout H. Base O-Ring (factory-installed in base of spout) I. Rubber Washer J. Mounting Nut K. T-Union Clip L. T-Union M. Waterlines N. Cold Valve O. Aerator Assembly O1. Aerator Washer O2. Aerator O3.
Faucet Dimensions 5
Faucet Dimensions 6
Lift Rod Drain Diagram and Parts List Dimensions 1 a 2 b 3 4 5 c d 6 e 7 f 8 g a. Drain Body e. Mounting Nut b. Rubber Washer f. Tailpipe Washer c. Concave Washer g. Tailpipe d.
Step1: Remove mounting hardware from spout Remove mounting nut (J), rubber washer (I), and base O-ring (H) G from spout (G) G H H I J I J Step 2: Secure Spout Install spout (G) throughGhole in sink or countertop with base O-ring (H) attached. Attach rubber washer (I) and mounting J nut (J) G H K B I J L A C E N J K A B E N A N B Adjust spout (G) to proper C position and tighten mounting nut (J) with adjustable wrench. D E Install t-union (L) onto supply line N of spout (G).
G G H Step 4: Remove hot & cold handles and base metal rings A B C G D E N H Remove handle (A) and base I metal ring (B) from valve (N). J Insert valve (N) into predrilled I hole (Hot: Left, Cold: Right) fromJ underneath. Repeat steps for second handle (A) and valve (F) G H J Step 5: Secure valves I J K L I J B C D E N O1 N O2 O3 N Secure base metal ring (B) and handle (A) onto valve (N) from above. Tighten mounting nut (E) A on valve (N) from underneath with adjustable wrench until snug.
Step 6: Connect waterlines to faucet and main valve F M N M L Thread waterlines (M) to hot and cold valve (F & N) horizontally. Thread other end of waterlines to t-union (L). Attach hot & cold supply lines (not included with faucet) to valves (F & N) vertically A. Hot Side: Left B. Cold Side: Right Secure other end of hot & cold supply lines to angle stops. Tighten all ends with adjustable wrench until snug. Turn on angle stops and check for leaks (DO NOT TURN ON FAUCET) Please Note: 1.
Step7: Install drain • Remove tail pipe (g), mounting nut (e), plastic washer (d), and concave washer (c) from drain body (a) a b c d e f g a b c d e f g a b c d e e f g • a b Install drain body (a), with rubber washer (b) attached, into the drain c hole. From underneath, attach d concave washere (c) (narrow end up), plastic washer (d), and mounting nut (e) to drain body (a). Secure tightly to sink with an adjustable wrench • Tighten mounting nut (e) with g snug.
Step7: Install drain A B C • Connect tailpipe (g) to p-trap D E N g Step 8: Flush faucet O1 O2 O3 Remove aerator assembly (O). Loosen aerator cover (O3) with adjustable wrench. Remove aerator (O2) and aerator washer (O1). Turn water on for 1 minute to remove any debris.
Replacement Part List - FUS-13803 1 8 9 10 2 17 3 4 5 6 7 11 16 12 13 13 15 14 1. Metal Handle 2. Cartridge - HOT 3. Base Metal Ring 4. Base O-Ring 5. Rubber Washer 6. Mounting Nut 7. Hot Valve 8. Aerator Washer 9. Aerator 10. Aerator Cover 11. Rubber Washer 12. Mounting Nut 13. T-Union Clip 14. T-Union 15. Waterline 16. Cold Valve 17.
Replacement Part List - Lift Rod Drain 1 2 3 1. Drain Cap 2. Drain Body 3. Rubber Washer 4. Concave Washer 5. Plastic Washer 4 6. Mounting Nut 5 8. Tailpipe 7.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 15 CAUSE ACTION Leakage under handles Hot or cold cartridge (2 or 17) may be loose Remove H & C metal handle (1). Tighten hot or cold cartridge (2 or 17) with adjustable wrench Aerator drips or has inconsistent water flow pattern Aerator (9) may be dirty Unscrew aerator cover or not seated properly (10) with adjustable wrench.
1 Push Open 2 3 Left Hot Water Care & Maintenance *To keep the product clean & shining, follow the steps below: 1. 2. 3. 4. Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives, or harsh cleaners Do not use cloth with a coarse surface Unscrew the aerator and clean when necessary *This installation manual is subject to change without further notice.
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1M 1.2GPM 4.5L/min maximum TM Water Efficiency HELP LINE Our customer service hours are Monday – Friday, 9am – 8pm EST. Be sure to visit our website at www.kraususa.com If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.
Download the Kraus Care & Maintenance Guide at: http://www.kraususa.com/maintenance www.kraususa.
R E G I S T E R Y O U R P R O D U C T T O D AY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit http://www.kraususa.com/registration We’re always looking for ways to improve. Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.
