INSTALLATION GUIDE Sheven Single Lever Vessel Faucet FVS-1002 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
10 1/8” (257mm) ∅ 1 15/16” Prior (∅ 50mm) ∅ 1 3/4” (∅ 45mm) • ∅ 1 15/16” (∅ 50mm) • 8 5/16” (21mm) to Installation: 1 3/8” (35mm) Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800775-0703 for a replacement Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List 1. 2. 3. 4. 5. 6. 7. 8. 9.
r Dimension Drawings 60 º 348 13 11/16” 60 º 348 13 11/16” 109 4 9/32” 226 109 8 7/8” 4 9/32” 226 8 7/8” Ø33-Ø35 Ø33-Ø35 Ø1 5/6”~Ø1 3/8” Ø1 5/6”~Ø1 3/8” Max x 35 Hot Water Cold Water Max x 35 Max 1 3/8” Max 1 3/8” Cold Water 4
13 11/16” 13 11/16” 109 109 226 226 4 9/32” 4 9/32” 8 7/8” 8 7/8” FVS-1002 Installation Procedures Ø33-Ø35Ø33-Ø35 Ø1 5/6”~Ø1 Ø1 5/6”~Ø1 3/8” 3/8” Step 1 Max x 35MaxMax x 35 Max 1 3/8” 1 3/8” Hot Water Hot Water Cold Water Cold Water (Suggested) Ø33~Ø35 hole Ø1.29”~Ø1.37” Remove rubber washer (4), metal washer (5), mounting nut (6) and mounting screws (7). Keep the base trim ring (2) and base O-ring (3) on the base of the faucet.
Step 3 After adjusting the direction of the faucet body (1), tighten the mounting nut (6) until snug and then tighten the mounting screws (7) to the nut with a Phillips head screw driver until snug. Step 4 Connect hot and cold waterlines (8) to the angle stops and tighten with a wrench.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE 10 Leakage under the handle Adjusting locking nut has come loose Hexagon Nut 9 11 12 13 Aerator drips or has inconsistent water flow pattern Aerator is dirty or not seated properly Water will not shut off completely Cartridge may be defective Close 25˚ ACTION Remove handle index button. Loosen set screw with hex wrench.
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1M 1.2GPM 4.5L/min maximum TM Water Efficiency FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. COMMERCIAL WARRANTY Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.