I N S TA L L AT I O N MA N UA L Sheven Single Lever Vessel Faucet FVS-1002 www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Congratulations on your new Kraus purchase! We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your Kraus experience. We welcome any questions or comments you may have, and look forward to assisting you in the future. For more information about Kraus products, please visit our website at: www.kraususa.com. In order to allow us to serve you better, we recommend registering your new Kraus product at: www.kraususa.
0 9 FVS-1002 Diagram and Parts List Included Parts: 9 1 9 1. 2. 3. 4. 5. 6. 7. 8. 9.
Dimension Drawings 13 1 Max Hot Water Cold Water Safety Tips • sh the • pes If soldering the water connections when installing the faucet, remove the O-rings, cartridges, and washers before applying any heat Protect your eyes with safety glasses when cutting or soldering
Dimension Drawings 60 º 348 13 11/16” 109 226 4 9/32” 8 7/8” Ø33-Ø35 Ø1 5/6”~Ø1 3/8” Max x 35 Max 1 3/8” Safety Tips • Do not overtighten fixing screws/nuts.
Ø33-Ø35 Ø1 5/6”~Ø1 3/8” 8 Max x 35 Max 1 3/8” Ø33-Ø35 Ø1 5/6”~Ø1 3/8” FVS-1002 Installation Procedures Cold Water Step 1 Hot Water Flush the pipes o t sassemble Max 1 3/8” Cold Water Remove rubber washer (4), metal washer (5), mounting nut (6) and mounting screws (7). Keep the base trim ring (2) and base O-ring (3) on the base of the faucet. (Suggested) Ø33~Ø35 hole Ø1.29”~Ø1.37” ole 37” uggested) 33~Ø35 hole .29”~Ø1.
Step 3 After adjusting the direction of the faucet body (1), tighten the mounting nut (6) until snug and then tighten the mounting screws (7) to the nut with a Phillips head screw driver until snug. Step 4 Connect hot and cold waterlines (8) to the angle stops and tighten with a wrench.
Hot Water Care & Maintenance *To keep the product clean & shining, follow the steps below: 1. 2. 3. 4. Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives, or harsh cleaners Do not use a cloth with a coarse surface Unscrew the aerator and clean when necessary *This installation manual is subject to change without further notice. Usage How to operate the handle: Raise the lever handle to turn on the water. Push down to turn off.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the handle Adjusting locking nut has come loose Remove handle index button. Loosen set screw with hex wrench. Remove handle by hand only. Tighten locking nut with an adjustable wrench Aerator drips or has inconsistent water flow pattern Aerator is dirty or not seated properly Unscrew aerator cap by hand.
Codes/Standards Applicable: Specified model meets or exceeds the following: ANSI/ASME A112.18.1, cUPC, AB1953 KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use. WHO IS COVERED BY THE WARRANTY This warranty extends to the original purchaser only.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller.
www.kraususa.