I N S TA L L AT I O N MA N UA L Coda Single Lever Vessel Faucet FVS-13800 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.
Thank you for purchasing Kraus We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future. For more information about Kraus products, please visit our website at: www.kraususa.
10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) 1 3/8” (35mm) ∅ 1 3/4” (∅ 45mm) ∅ 1 15/16” (∅ 50mm) Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-7750703 for a replacement • 9/16”-18UNEF • Turn off the hot and cold water supply at the angle stops and turn on the old 1 1/4-18UNF-2A faucet to release any built up pressure. Remove existing faucet.
FVS-13800 Diagram and Parts List I A. Faucet Body B. Base O-Ring C. Rubber Washer H1 H2 H3 D. Metal Washer E. Mounting Nut F. Mounting Screws G. Hot & Cold Waterlines H. Aerator Assembly A H1. Aerator Washer B C D E F G H2. Aerator H3. Aerator Cover I.
Faucet Dimensions Max35 Max1 3/8” ∅48 ∅1 7/8” ∅33~∅35 ∅1 5/16”~∅1 3/8” 267 10 1/2” 136 5 3/8” 235 9 1/4” 337 13 1/4” 15º
Step1: Install mounting hardware and waterlines A A B B C G D E F Remove mounting nut (E) with mounting screws (F) attached. Remove metal washer (D), and rubber washer (C) from threaded mounting pipe. Place faucet body (A) on a soft cloth, spout facing up. Secure the hot & cold waterlines (G) at the base of the faucet (HAND-TIGHTEN ONLY) A. Hot Side: Left B.
Step 3: Secure faucet A A B After B adjusting direction of faucet body (A), tighten mounting nut (E) with adjustable wrench until snug. Secure mounting nut (E) by tightening mounting screws (F) C a Phillips head screwdriver with G E F D E F G Step 4: Connect waterlines to faucet and main valve Thread hot & cold waterlines (G) onto angle stops and tighten with adjustable wrench until snug.
Step 5: Flush faucet Remove aerator assembly (H). Loosen aerator cover (H3) with adjustable wrench. Remove aerator (H2) and aerator washer (H1). Turn water on for 1 minute to remove any debris. Reassemble aerator assembly (H) H1 H2 H3 Replacement Part List - FVS-13800 3 2 4 1 5 6 7 17 8 9 10 15 11 12 13 14 16 1. Metal Handle 2. Set Screw 3. Cover Button 4. Cartridge Cover 5. Locking Nut 6. Cartridge 7. Aerator Washer 8. Aerator 9. Aerator Cover 10. Base O-Ring 11. Rubber Washer 12.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE 10 Leakage under the 9 handle 11 Locking nut (5) has Hexagon Nut come loose 12 13 ACTION Remove cover button (3). Loosen set screw (2) with hex wrench (17). Remove metal handle (1). Unscrew cartridge cover (4) (by hand only).
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R &T NSF/ANSI 61 ASME A112.18.1M 1.5GPM 5.7L/min maximum TM Water Efficiency KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use. WHO IS COVERED BY THE WARRANTY This warranty extends to the original purchaser only.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller.
www.kraususa.