R INSTALLATION MANUAL Dex Stainless Steel Undermount Kitchen Sinks TM KA1AS17B / KA1AS25B / KA1UD33B / KA1US17B / KA1US21B / KA1US25B / KA1US32B / KA1US33B / KD1US17B / KD1US25B / KD1US33B / KD1UD33B www.kraususa.com I Toll Free: 1.800.775.0703 I © 2020 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Inspect the sink prior to installation to make sure that it has not been damaged during shipping. · Use the cut-out template provided by Kraus. · Observe all plumbing and building codes according to your state requirements. · Not recommended to be installed with laminate countertop.
Tools you will need: Safety Goggles Drill Silicone Adhesive Jig Saw Scissors Phillips Screwdriver Tape Measure Pencil Screwdriver Putty Knife NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Undermount sinks with countertop materials other than wood, marble or granite.
Parts List KA1AS17B · Cut-Out Template · Mounting Hardware KA1AS25B · Cut-Out Template · Mounting Hardware KA1UD33B · Cut-Out Template · Mounting Hardware · Strainer ST-4 x 2 · Bottom Grid BG1517 x 2 KA1US17B · Cut-Out Template · Mounting Hardware · Strainer ST-4 · Bottom Grid BG1517 KA1US21B · Cut-Out Template · Mounting Hardware · Strainer ST-4 · Bottom Grid BG1915 KA1US25B · Cut-Out Template · Mounting Hardware · Strainer ST-4 · Bottom Grid BG2317 KD1US17B · Cut-Out Template · Mounting Hardware · Strain
23" (585mm) 5 1/2" 18 7/8" (480mm) (140mm) 7/8" (22mm) (162mm) 7/8" (22mm) R1 1/2" 6 3/8" 5 1/2" (140mm) KA1AS25B 24 3/4” x 18 7/8” x 5 1/2” Min Cabinet Size: 30” (162mm) 6 3/8" KA1AS17B 16 7/8” x 18 3/4” x 5 1/2” Min Cabinet Size: 21” (22mm) KA1UD33B 32 7/8” x 18 3/4” x 9” Min Cabinet Size: 36” (22mm) 7/8" 15 1/8" (385mm) 7/8" 17" (432mm) 18 3/4" (476mm) (62mm) typ.
/8" 23" (585mm) (22mm) 24 3/4" (629mm) 9" (229mm) (195mm) 7 3/4" 21 1/4" (540mm) 7/8" 17 1/8" (435mm) 18 7/8" (479mm) 6 3/8" (163.5mm) (485mm) (40mm) 19" 17 3/4" (451mm) 8 3/8" (212.5mm) R1 1/2" (20mm) typ. R2 1/2" R1 3/8" 30" (62mm) typ.
Dimensions R 1 5/8" 3 1/2" 17" (432mm) 18 3/4" (476mm) (91mm) 3" (76mm) 7/8" (22mm) 9" (229mm) 24 3/4" (629mm) (229mm) R 1 5/8" R 1 5/8" (40mm) (40mm) KD1US17B 16 7/8” x 18 3/4” x 9” Min Cabinet Size: 21” KD1US25B 24 3/4” x 18 7/8” x 9” Min Cabinet Size: 30” R 1 5/8" 7/8" 3 1/2" (91mm) (22mm) typ.
1. Determine Reveal Type Use scissors to cut along the line of the paper template for your desired reveal type (Negative, Positive or Flushed Reveal).
2. Position Template · · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. 3. Trace Template · Trace template on countertop with a pencil.
4. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
5. Set up Mounting Brackets · · Turn countertop over and align sink with countertop. Decide location for mounting brackets. Mounting holes should be 1/2" from edge of sink. 1/2" (13mm) 6. Drill Hole in Countertop · Drill 3/8" diameter x 1/2" deep hole in countertop.
7. Install Anchors · Insert anchors into drilled holes and lightly tap with a hammer until flush. 8. Secure Sink to Countertop · Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly.
9. Attach Mounting Hardware · · Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
10. Install Plumbing Fixtures · · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC certification.
Codes/Standards Applicable: UP C C R Kitchen Sink Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Kitchen Sink” in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product.
Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded. No additional warranties, express or implied, are given, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
