R INSTALLATION MANUAL Indy Single Lever Basin Faucet TM KBF-1401 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Flush angle stops to release any debris prior to installation.
Diagram and Parts List A B C G D E A. B. C. D. E. 4 Faucet Body Metal Base Ring Rubber Washer Metal Washer Lock Nut F. G.
Faucet Dimensions Ø2" (50mm) 1 3/8" (35mm) 15° 6 1/4" (159mm) 5 1/8" (131mm) 4 5/8" (117mm) 3 3/8" (86mm) 5/16-18UNC Ø1 3/8" (35mm) 9/16"-UNEF-24 Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Install faucet and mounting hardware Place the faucet (A) through the mounting holes in the sink until the faucet (A) sits on top of the sink. Secure the faucet (A) to the sink using the rubber (C) and metal washers (D) and lock nut (E) provided. Ensure the washers (C&D) and waterlines have no interference. A C&D E C D E F Step 2. Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug. Turn on angle stops and check for leaks.
Replacement Parts Replacement Parts List 1 2 4 3 Finish/Color Part # 1. Metal Handle SFS,MB,CH,BG* KP06177 2. Handle Button GR, BL, YL* KP06026 3. Set Screw M5x6RB 5 4. Cartridge Cover 8 6 7 14 KP06052 SFS,MB,CH,BG* KP06059 6. Locking Nut KP06176 7. Cartridge KP06101 KP06183 8. Aerator 9. Metal Base Ring 9 12 10 11 15 13 KP06080 5. O-Ring SFS,MB,CH,BG* KP06181 10. Rubber Washer KP06179 11. Metal Washer KP06178 12. Mounting Nut KP06182 13. Spanner Key KP06180 14.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the faucet Bonnet nut has come loose. Remove the index. Loosen set screw with hex wrench. Remove the handle. Unscrew cap (by hand only). Tighten bonnet nut with an adjustable wrench. Cartridge may need to be adjusted or replaced. Remove the index. Loosen set screw with hex wrench. Remove the handle.
Codes/Standards Applicable: LEAD FREE NSF/ANSI 372 UP C IA C R PM OR C NSF/ANSI 61 &T ASME A112.18.1 1.2GPM 4.5L/min maximum R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
