I N S TA L L AT I O N MA N UA L Solinder Double Handle Widespread Basin Faucet KEF-15603 www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Thank you for purchasing Kraus We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future. For more information about Kraus products, please visit our website at: www.kraususa.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List 1 8 9 2 3 26 4 27 5A 5B 5C 13 5D 6 14 15 10 11 16 17 18 25 19 12 22 23 24 21 20 7
12 Diagram and Parts List 1 2 3 4 5 6 7 8 1. 2. 3. 4. 5. Hot Handle Valve with Waterline Faucet Body Cold Handle Valve with Waterline Rubber Washer Mounting Kit (A) Rubber Washer (B) Metal Washer (C) Mounting Nut (D) Mounting Screws 6. Hot & Cold Waterlines 7. Three Way Connector 8. Lift Pole Knob 9. O-ring 10. Lift Pole Rod 11. Connector (located inside faucet body) 12. Lift Pole Extension 13. Waste Stopper 14. Drain 15. Rubber Washer 16. Concave Washer 17. Plastic Washer 18. Mounting Nut 19.
91mm (3.58”) 49mm (1.93”) 148 mm (5.82”) Faucet Installation Procedure 116 mm (4.
2-M10X1 Max30mm (1.
Step 1 Step 2 Step1: Remove mounting hardware and three-way connector 1 1 Remove three-way connector (7) from faucet body (2).
5C 5D 7 Step 3: Connect waterlines to valves Attach hot waterline (6) to hot handle valve (1) and cold waterline (6) to cold handle valve (3). Hand-tighten. Thread other end of hot & cold waterlines to three-way connector (7) and tighten with adjustable wrench Connect flex water supply lines to angle stops and tighten with adjustable wrench.
Step 4: Install drain 1. Remove waste stopper (13) from drain (14). Remove drain body (19), mounting nut (18), plastic washer (17), and concave washer (16) from drain (14) 2. From underneath, insert lift pole extension (12) to faucet body and attach to lift pole rod (10) using connector (11) inside faucet body (2). Secure tightly 3. Install drain (14), with rubber washer (15) attached, into the drain hole 4.
TO NGLE Step4 Step 4: (Continued) 13 14 15 10 11 16 17 18 25 19 12 22 23 24 21 20
Step 5: Flush faucet Step5 26 27 After installing faucet, remove aerator (26) with included aerator key (27). Turn water on for 30 seconds to remove any debris.
Close 25˚ 90˚ Care & Maintenance Push *To keep the product clean & shining, follow the steps below: Open 1. 2. 3. 4. Left Hot Water Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives, or harsh cleaners Do not use cloth with a coarse surface Unscrew the aerator and clean when necessary *This installation manual is subject to change without further notice.
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1M 1.5GPM 5.7L/min maximum TM Water Efficiency KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use. WHO IS COVERED BY THE WARRANTY This warranty extends to the original purchaser only.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller.
www.kraususa.