R INSTALLATION MANUAL Fireclay Dual Mount Kitchen Sink KFD1-24GWH / KFD1-30GWH www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Inspect the sink prior to installation to make sure the sink has not been damaged during shipping. · Observe all plumbing and building codes according to your state requirements. · Additional floor and wall preparation may be required to avoid damaging the sink. · Make sure to purchase the correct cabinet for your kitchen sink. Base cabinets should be 3" larger than the actual size of the sink. · Not recommended to be installed with laminate countertop.
Tools you will need: ACETONE Safety Goggles Drill Silicone Adhesive Jig Saw Acetone Phillips Screwdriver Tape Measure Pencil Screwdriver Level NOTE: Specialized tools may be necessary to install Kraus Fireclay sinks with countertop materials other than wood, marble or granite. R 1" 21 3/4" (551mm) (25mm) 18 1/8" (460mm) 27 1/2" (700mm) 9" 10" (254mm) (228.
Undermount Installation 1. Measure & Build Supports Build supports on inside of cabinet based on sink measurements · Installer Tip: Support options · · · 1 1/4" Angle Irons (2) 2" x 4' NOTE: Due to the typical ±3mm side wall variance in manufacturing, it is recommended that you design / modify the sink cabinet to match your clients individual sink(s) need.
2. Install Sink · Place sink in opening. The weight of sink should be sustained by the built supports.
3. Cut Countertop · · Kraus recommends providing the cabinet maker with the actual sink to be installed prior to the cabinet fabrication. It is recommended that the sink be installed with an approximately 1/8" positive reveal. It is further recommended that the installer(s) discuss this with the customer and agree that this finished appearance is the desired effect.
4. Install Countertop Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place countertop cutout hole over sink and press firmly. hesive Installer Tip: Use acetone or denatured alcohol to remove any excess sealant.
5. Installing Plumbing and Fixtures · Connect drain, trap to drain and water supply connections to the faucet according to manufacturer's instruction. · Run water into sink and check for leaks. · Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC certification.
Top Mount Installation 1. Measure & Build Supports · Build supports on inside of cabinet based on sink measurements · The supports should be flush with the top of the cabinet Installer Tip: Support options · · · 1 1/4" Angle Irons (2) 2" x 4' NOTE: Due to the typical ±3mm side wall variance in manufacturing, it is recommended that you design / modify the sink cabinet to match your clients individual sink(s) need.
2. Position Template · Check the cut-out template against the actual sink to ensure a proper sized cut-out. · Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. e plat m r Te ape P 3. Trace Template · Trace template on countertop with a pencil.
4. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
Step 5. Apply Silicone or Plumber's Putty Clean and dry the surface around the opening of the sink. · Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included) underneath the edge of the sink.
Step 6. Secure Sink to Countertop · · · · Insert the sink into the opening, check the alignment of the sink to the cutout in the countertop and press firmly. Remove excess silicone-based sealant. Allow sealant to set for 30-60 minutes. Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC certification.
Codes/Standards Applicable: UP C C R Fireclay Kitchen Sink Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Fireclay Kitchen Sink” in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for a period of five (5) years.
Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded. No additional warranties, express or implied, are given, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.