I N S TA L L AT I O N MA N UA L Crespo™ Single Lever Pull Down Kitchen Faucet KPF-2720 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
7/8” (22mm) 19.7 º Prior to Installation: • 10 1/8” 8 5/16” Make(257mm) sure you have all necessary (21mm) parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at ∅ 1 15/16” 800-775-0703 for a replacement (∅ 50mm) ∅ 1 3/4” • (∅ 45mm) ∅ 1 15/16” (∅ 50mm) • 1 3/8” (35mm) Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List A. Spray Head B. Faucet Body B C. Deck & Putty Plate D. Base A D E. Spray Hose F. Supply Hose G. Hot & Cold Waterlines J H. Weight I. Quick Connect J. Hex Wrench Set C J1. 2.5mm J2.
Faucet Dimensions 10-1/8” (257mm) 10-1/8” (258mm) 4-3/8” (110mm) 16-1/4” (413mm) 8-3/8” (213.5mm) 8-1/4” (209mm) 2-1/2” (63mm) 24-1/2” (622.7mm) 1-5/8” (40mm) 1/16”~1-1/8” (1mm~30mm) 6-5/8 (169.
Step 1A: Install base without deck & putty plate 1A 1B Insert base (D) into sink or countertop with “FR↑NT” facing forward.
Step 1B: Install base with deck & putty plate 1B Place a bead of clear silicone sealant (not included) around the D edge of the putty plate (C). Secure 2 deck & putty plate (C) on sink or countertop. Insert base (D) into hole of deck & putty plate (C) with “FR↑NT” facing forward.
Step 2: Install faucet G G G B E Remove Quick Connect (I) from spray hose (E). Insert spray hose (E) into small hole of base (D). Insert hot & cold waterlines (G) and supply hose (F), one by one, in large hole of base G F F B D D Step 3: Secure faucet Align arrow on faucet body (B) with arrow on base (D). Attach faucet body (B) to base (D) and turn counter-clockwise. Secure faucet body (B) by tightening the set screw with 2.
B E D G Step 4: Connect waterlines to main valveF F Thread hot & cold waterlines B (G) onto angle stops. Tighten with adjustable wrench until D snug. Turn on the angle stops and check for leaks (DO NOT TURN FAUCET ON) G D G Hot Installer Tip: Use two wrenches when securing waterlines to angle stops to prevent kinking, as shown in picture G Cold Step 5: Connect quick connect F I er Cap Rubber Cap E E I E I E Attach Quick Connect (I) to spray hose (E).
Step 6: Install weight G G Hot Hot G Attach weight (H) on the Cold designated mark on the spray hose (E) G Cold Designated Mark A E H Step 7: Flush faucet Remove spray head (A). Hold tip of spray hose (E). Turn faucet on for 1 minute to flush any debris.
Replacement Part List 1. A Index Button B Set Screw 10 2. Metal Handle 6 3. Cartridge Cover 7 4. Locking Nut 5. Cartridge 5 8 3 4 6. Plastic Cover 7. Spray Head 9 2 8. Set Screw 1 9. Cover & Putty Plate 11 10. Quick Connect Assembly 12 14 15 11. Spray Hose 12. Weight 13. Base 13 Index Button Metal Handle Trim Cap Locking Nut Ceramic Disc Cartridge Pattern Clip Handle Spray w/Check Valve Screw 14. Hex Wrench 2.5mm 15.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 11 CAUSE ACTION Leaking from spray hose Quick Connect (10) may Remove Quick Connect be installed incorrectly (10) from spray hose (11) and reinstall. Make sure you hear a click when you install it on the spray hose (11) Water will not shut off completely Cartridge (5) may need to be adjusted or replaced Remove index button (1A).
Care & Maintenance e 25˚ *To keep the product clean & shining, follow the steps below: 90˚ 1. Rinse with clean water & dry with a soft cloth Push cleaners 2. Do not clean with soaps, acid, polish, abrasives, or harsh 3. Do not use cloth with a coarse surface Left Open 4.Hot WaterUnscrew the aerator and clean when necessary *This installation manual is subject to change without further notice. Download the Kraus Care & Maintenance Guide at: http://www.kraususa.
Codes/Standards Applicable: GREEN LEAD FREE IA P NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO MO Meets ASME A112.18.1M/A112.18.1 R& T 1.75GPM 6.6L/min maximum TM Water Efficiency HELP LINE Our customer service hours are Monday – Friday, 9am – 8pm EST. Be sure to visit our website at www.kraususa.com If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc.
www.kraususa.
R E G I S T E R Y O U R P R O D U C T T O D AY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit http://www.kraususa.com/registration We’re always looking for ways to improve. Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.
