I N S TA L L AT I O N MA N UA L Single Lever Pull-Down Kitchen Faucet KPF-1630 www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800-775-0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List 12 6 1 5 2 9 11 8B 8A 7 3A 3B 4A 4B 4C 10
13 Diagram and Parts List 1 2 3 4 5 6 7 8 1. Spray Head 2. Faucet Body 3. Deck Plate Assembly A. Deck Plate B. Base Plate 4. Mounting Hardware A. Rubber & Metal Washer B. Mounting Nut C. Mounting Screws 5. Spray Hose 6. Weight 7. Check Valve 8. Hot and Cold Copper Lines A. Cold B. Hot 9. Aerator Key 10. Hex Wrench 11. Faucet Extender Tools you will need Adjustable Wrench Silicone Sealant (optional) Phillips Screwdriver 12.
M33X1.5 M33X1.5 Installer Tip: Shut off main water supply before installing new faucet 5.35” 9.3” (136mm) 5.35” (236mm) 9.3” (136mm) (236mm) 9.2” (233.8mm) 9.2” (233.8mm) 3.95”3.95” (100.5mm) (100.5mm) 6.7” (170.5mm) 2.87” 6.7” (73mm) (170.5mm) 2.87” (73mm) 4.9” (125mm) 4.9” (125mm) 5º 5º 18.6” (472.3mm) 18.6” (472.3mm) Faucet Installation Procedure 8.3” 8.3” (211.4mm) (211.
STEP1 Step 1: Remove mounting hardware STEP 2A STEP 2B Remove the mounting screws (4C), mounting nut (4B), and rubber & metal washer (4A) from the mounting pipe 4A 3A 3B 4B 4C 1 STEP 2A STEP 2B STE Step 2A: Faucet installation - with deck plate For three-hole installation: STEP 5(3A), base plate Deck plate (3B), and silicone sealant (optional) are required STEP 4 4B 4C 4A 4B 4C 3A 3B 7 5 6
STEP 2B STEP 3 Step 2B: Faucet installation - without deck plate For single-hole installation: Deck plate (3A), base plate (3B), and silicone sealant are NOT required STEP 3 3A Step 3B 3: Install faucet and mounting hardware STEP 6 4A 4B Insert faucet body4C (2) into hole in countertop or deck plate assembly (3).
STEP 4 STEP 5 Step 4: Secure mounting hardware 4B 4C A B C 3A 3B Adjust direction of faucet body (2) so that handle is on right side of faucet. Tighten mounting nut (4B) until snug. Tighten mounting screws (4C) to nut with a Phillips screwdriver until snug STEP 5 Step 5: Attach spray hose and counterweight STEP 6 Connect spray hose7(5) to 5 to check valve (7) attached supply line.
STEP 6 Step 6: Connect waterlines STEP 7 5 4A 4B 4C 4A 8 4B 4C STEP 4 6 1 Connect waterlines (not included) to hot and cold copper lines (8). Connect waterlines (not included) to angle stops. Tighten both 3A 3B ends of waterlines with a wrench until snug. Turn on hot and cold angle stops STEP 5and check for leaks STEP 6 STEP 7 Step 7: Flush spray hose Remove spray head (1) from spray hose (5). Hold tip of spray hose (5).
Replacement Parts 1. a. Aerator b. Spray Head 24 10 3 Hexagon Nut 9 4 11 12 2 13 1B 5 7 10 9 Spray Hose 4. Hose Guide 5. Handle Button 6. Set Screw 7. Metal Handle 8. Cartridge Cover 9. Locking Nut 11. Cartridge Housing Hot 12. Deck Plate Water 17 15 16 13. Base Plate 19 14. Rubber & Metal Washer 20 15. Mounting Nut 17. Protective Sleeve 18 90˚ 19. Aerator Key 20. Faucet Extender 21. Hex Wrench Push 22. Check Valve Open Left Hot Water 23. Connector 24.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand.
8 Maintenance - Cartridge Replacement 5 1 Step 1: Remove button located at the top of the handle. Loosen the set screw with a hex wrench. Remove the handle and unscrew cartridge cover by hand Step 2: Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge Step 3: Place the new cartridge in the handle seat.
Codes/Standards Applicable: GREEN LEAD FREE IA P NSF/ANSI 372 NSF/ANSI 61-9 MO R &T Meets ASME A112.18.1M/A112.18.1 1.8gpm 6.8L/min maximum TM Water Efficiency KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller.
www.kraususa.
