I N S TA L L AT I O N MA N UA L Single Handle Pull-Down Kitchen Faucet KPF-1670 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List 12 6 1 2 9 10 11 13 2 5 8B 8A 7 3A 3B 4A 4B 4C 3
12 Diagram and Parts List 1 2 3 4 5 6 7 8 1. Spray Head 2. Faucet Body 3. Deck Plate Assembly A. Deck Plate B. Base Plate 4. Mounting Hardware A. Rubber & Metal Washer B. Mounting Nut C. Mounting Screws 5. Spray Hose 6. Weight 7. Quick Connector 8. Hot and Cold Copper Lines A. Cold B. Hot 9. Aerator Key 10. Hex Wrench 11. Faucet Extender 12. Washer 13 Tools you will need Adjustable Wrench Silicone Sealant (optional) Phillips Screwdriver 13.
Faucet Installation Procedure Installer Tip: Shut off main water supply before installing new faucet
STEP1 Step 1: Remove mounting hardware STEP 2A STEP 2B 2 1 Remove the mounting screws (4C), mounting nut (4B), and rubber & metal washer (4A) from the mounting pipe STEP 8 4A 3A 3B 4B 4C STEP 2A STEP 2B STE 4B 4C Step 2A: Faucet installation - with deck plate 2 3 ForSTEP three-hole installation: 5 Deck plate (3A), base plate (3B), and silicone sealant (optional) are required STEP 4 S STEP 4 4B 4C 4B 4C 4A 4A 3A 3B 4B 4C 8 7 5 6 1 STEP 8 2
Step 2B: Faucet installation - without deck plate 2 1 For single-hole installation: Deck plate (3A), base plate (3B), and silicone sealant are NOT required STEP1 STEP 2A S Step 3: Install faucet and mounting hardware 3 44 Insert faucet body (2) into hole in countertop or deck plate assembly (3).
Step 4: Secure mounting hardware Adjust direction of faucet body (2) so that handle is on right side of faucet. Tighten mounting nut (4B) until snug. Tighten mounting screws (4C) to nut with Phillips screwdriver until snug 4B a 4C b c d e Step 5: Attach spray hose and counterweight 5 6 Connect spray hose (5) to quick connector (7) attached to supply line.
Step 6: Connect waterlines 6 7 7 Step 7: Flush spray hose 5 1 Connect waterlines (not included) to hot and cold copper lines (8). Connect waterlines (not included) to angle stops. Tighten both ends of waterlines with a wrench until snug. Turn on hot and cold angle stops and check for leaks 8 Remove spray head (1) from spray hose (5). Hold tip of spray hose (5).
Replacement Parts 23 25 10 21 4 22 Hexagon Nut 9 3 11 2 12 5 1 13 6 7 13 12 11 10 14 24 15 16 17 18 19 9 8 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 26 Close 25˚ 90˚ 20 Open Left Hot Water 27 24. 25. 26. 27.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand.
3 44 Maintenance - Cartridge Replacement 1 2 3 2 Step 1: Remove button located at the top of the handle. Loosen the set screw with a hex wrench. Remove the handle and unscrew cartridge cover by hand 3 Step 2: Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge Step 3: Place the new cartridge in the handle seat.
Codes/Standards Applicable: GREEN LEAD FREE IA P NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO MO Meets ASME A112.18.1M/A112.18.1 R& T 1.75GPM 6.6L/min maximum TM Water Efficiency FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
R E G I S T E R Y O U R P R O D U C T T O D AY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit http://www.kraususa.com/registration We’re always looking for ways to improve. Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.