INSTALLATION GUIDE Oletto™ Single Lever Pull Down Kitchen Faucet KPF-2620 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep teh box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
7/8” (22mm) 19.7 º Prior to Installation: • 10 1/8” 8 5/16” Make(257mm) sure you have all necessary (21mm) parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800- ∅ 1 15/16” 775-0703 for a replacement (∅ 50mm) ∅ 1 3/4” • (∅ 45mm) ∅ 1 15/16” (∅ 50mm) • 1 3/8” (35mm) Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List A. Spray Head B. Faucet Body C. Deck & Putty Plate B D. Supply Hose E. Hot & Cold Waterlines A F. Spray Hose G. Weight H. Quick Connect I. Hex Wrench i1. 2.5mm i2. 4mm J.
Faucet Dimensions 10 1/2" 10 1/4" 267mm 260mm 8 3/4" 4 1/4" 400mm 186mm 7 1/4" 208mm 8 1/4" 15º 15 3/4" 221mm 109mm 62mm 620mm 24 1/2" 40mm 1 5/8" 1mm~30mm 1/16"-1 1/8” 2 1/2" Check Value 9/16-24UNEF 3/8” Compression 4
Step 1A: Install base without deck & putty plate Insert base (J) into sink or countertop with “FR↑NT” facing forward.
Step 1B: Install base with deck & putty plate Place a bead of clear silicone sealant (not included) around the edge of the putty plate (C). Secure deck & putty plate (C) on sink or countertop. Insert base (J) into hole of deck & putty plate (C) with “ FR↑NT” facing forward.
Step 2: Install faucet E E D F F E Remove Quick Connect (H) from spray hose (F). Insert spray hose (F) into small hole of base (J). Insert hot & cold waterlines(E) and supply hose (D), one by one, in large hole of base D D Step 3: Secure faucet Align arrow on faucet body (B) with arrow on base (J). Attach faucet body (B) to base (J). Secure faucet body (B) by tightening the set screw with 2.5mm hex wrench (i1) B J i1 Note: “ “ on base should be in alignment with “ “ on faucet body.
Step 4: Connect waterlines to main valve E Installer Tip: Use two wrenches when securing waterlines to angle stops to prevent kinking, as shown in picture E E Hot Thread hot & cold waterlines (E) onto angle stops. Tighten with adjustable wrench until snug. Turn on the angle stops and check for leaks (DO NOT TURN FAUCET ON) Cold Step 5: Connect quick connect D Attach Quick Connect (H) with black end onto spray hose (F) until you hear a click.
Step 6: Install weight Attach weight (G) on the designated mark on the spray hose (F) F Designated Mark A F G Step 7: Flush faucet Remove spray head (A). Hold tip of spray hose (F). Turn faucet on for 1 minute to flush any debris.
Replacement Part List 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 10 Hexagon Nut 9 11 3 2 12 13 4 1 6 5 7 11 13 12 8 9 10A 10B 14 15 Close 25˚ Open 16 17 18 90˚ 11. 12. 13. 14. 15. 16. 17. 18. Spray Head Washer Hose Guide Spout Clip Set Screw Catridge Locking Nut Catridge Cover Metal Handle A Set Screw Cold BHot Index Button Water Water Cover Plate Putty Plate Quick Connect Assembly Spray Hose Weight Base Hex Wrench (2.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 11 CAUSE ACTION Leaking from spray hose Quick Connect (8) may be installed incorrectly Remove Quick Connect (8) from spray hose (9) and reinstall. Make sure you hear a click when you install it on the spray hose (9) Water will not shut off completely Cartridge (5) may need to be adjusted or replaced Remove index button (1A).
Codes / Standards Applicable: GREEN LEAD FREE IA P NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO MO Meets ASME A112.18.1M/A112.18.1 R& T 1.75gpm 6.6L/min maximum TM Water Efficiency FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
