INSTALLATION MANUAL Oletto™ Single Handle Commercial Style Kitchen Faucet KPF-2631 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I Rev.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List B I A J C D E F G H A. Sprayer B. Faucet Body C. Escutcheon D. Gasket E. Easy Install Assembly F. Weight 4 G. Weight Clip H. Quick Connector I. 2.5mm Hex Wrench J.
Faucet Dimensions 10 3/4" 10 1/4" [274.6mm] 11" [279.6mm] [259mm] 9 1/8" 8 1/4" [209.5mm] [549mm] 21 5/8" 8 1/2" [215.4mm] [555mm] 21 7/8" [233.2mm] 2" [52mm] [59.6mm] 2 1/8" [54.1mm] [62mm] Max: 2 3/8'' 2 1/2" 3/8”-compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1a: Installing the easy install assembly (without escutcheon) Shut off the water supply. Remove the old faucet. Clean the mounting surface. Check for the proper thickness of the sink or countertop. Insert the base (a) into the sink or countertop. If your model does have a escutcheon, skip to step 1 b. a b NOTE: “Front” on the base (a) must face the front of the sink or countertop. The two mounting plates (b) b) on the base (a) must be loose movable during the installation of the base (a).
Step 2: Installing the easy install assembly J J a Fig 1 a C C b 1 b 1 Fig 2 J J a a C b Fig 4 1 C b Fig 3 1 Press the base (a) so that it can not move, then turn the screw with the provided hex wrench (C, HEX: 6.0mm) clockwise, as shown in Fig 1. When the mounting plates (b) make contact with the sink (1), continue to turn the screw with the provided hex wrench (C, HEX: 6.0mm) clockwise, as shown in Fig 2, until the base (a) is completely tightened and secured, as shown in Fig 4.
Step 3: Installing the faucet B I 3 2 1 a Insert the hose (1), supply lines (2) and quick connect hose (3) one by one through the hole of the base (a). Carefully insert the hoses into the base. Place the faucet assembly onto the base (a) as shown in the above figure. Secure the faucet assembly (B) by tightening the set screw with the provided hex wrench (I, Hex: 2.5 mm).
Step 4: Installing the counterweight Install the weight clip (G) at the point of the hose marking "weight here". Insert the weight (F) onto the weight clip (G) by sliding it down onto the weight clip (G). Weight here F Weight here G Step 5: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON). NOTE: Please make sure filter washers are installed before connecting to the main valve.
Step 6: Flush faucet Pull the hose assembly out of the spout and remove the spray head (A) by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks. Retighten any connections if necessary, but do not overtighten.
Replacement Parts Replacement Parts List Finish / Color 1. Sprayer BB, CH, SFS, MB, KP27250 SFACB** 2. Washer KP27251 3. Sprayer Hose 04 03 4. Spring Assembly 05 5. Inverter 06 07 02 01 08 12 19 20 10 23 KP27255 GR, BL** KP27256 11 9. Bonnet Nut KP27258 12 13 10. Cap 14 18 KP27254 KP27257 11. Handle 22 GR, BL** 8. Cartridge 09 17 21 BLBB, GRCH, KP27252 GRSFS, BLMB, BLSFACB* BB, CH, SFS, MB, KP27253 SFACB** 6. O-ring 7.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the handle. Bonnet nut ( ) has come loose. 5HPRYH WKH LQGH[ /RRVHQ WKH VFUHZ ZLWK WKH KH[ ZUHQFK 5HPRYH WKH KDQGOH DQG FDS 7LJKWHQ WKH ERQQHW QXW ZLWK DQ DGMXVWDEOH ZUHQFK The aerator has an irregular or reduced water flow. The aerator is dirty or misfitted.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI/CAN 61: Q ≤ 1 UP C R C LEAD FREE IA P C MO R& R NSF/ANSI 61 T TM ASME A112.18.1 1.8GPM 6.8L/min maximum Faucet - Lifetime Limited Warranty Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com R If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
