INSTALLATION GUIDE Oletto™ Single Handle Pull Down Kitchen Faucet KPF-2820 KPF-2821 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2021 Kraus USA Plumbing LLC I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List A B C D E F J G H I A. Faucet Body B. Flange C. Rubber Washer D. Metal Washer E. Mounting Nut 3 F. Screws G. Weight H. Weight Clip I. Quick Connector J.
Faucet Dimension (For KPF-2821) 12 1/2" [318.9mm] 3 1/2" 10 7/8" 10 1/2" [265.5mm] 20 3/8" [275.0mm] [517.6mm] [90.1mm] Ø2 1/4" 3" [76.5mm] [57.
Faucet Dimension (For KPF-2820) 10 5/8" [270.7mm] 3 1/2" 8 3/4" [222.9mm] 16 5/8" [423.7mm] [90.1mm] 8 7/8" [227.0mm] Ø2 1/4" 3" [76.5mm] [57.
Step 1: Installing the faucet A F (2N.m Max) E Shut off the water supply. Place faucet (A) through the hole in countertop. Secure the faucet (A) to the countertop using the rubber washer (C), metal washer (D) and mounting nut (E) provided. Tighten screws (F). C D F Step 2: Securing the faucet assembly Push the quick connector (I) firmly upward and attach it to the receiving block (a). Pull down moderately to ensure the connection has been made.
Step 3: Securing the faucet assembly Install the weight clip (H) at the point of the hose marking "weight here". Insert the weight (G) onto the weight clip (H) by sliding it down onto the weight clip (H). Weight here G Weight here H Step 4: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug. Turn on angles stops and check for leaks (DO NOT TURN FAUCET ON) NOTE: Please make sure filter washers are installed before connecting to the main valve.
Step 5: Flush faucet Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This Fushesaway any debris that could cause damage to internal parts. Check for leaks. Re-tighten any connections if necessary, but do not overtighten.
Replacement Parts Replacement Parts List Finish / Color Part # SFS, MB, SFSB, SFACB, BB, CH* KP27207 1. Sprayer Head KP27208 2. Sprayer Washer 21 3. Sprayer Hose 3 4 5 2 1 6 7 8 9 17 18 19 20 4. O-ring KP27210 5. Inverter KP27211 6. Cartridge KP27069 7. Bonnet Nut KP27202 8. Cap & O-ring 10 11 KP27209 GRSFS, BLMB, BLSFACB, BLBB, (For KPF-2820) BLSFSB,GRCH* KP27233 (For KPF-2821) 9. Handle SFS, MB, SFSB, SFACB, BB,CH* SFS, MB, SFSB, SFACB, BB,CH* KP27203 KP27204 KP27001 10.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: 10 PROBLEM CAUSE Leakage under the 9 handle Bonnet nut (7) has Hexagon Nut come loose 11 12 13 The aerator is dirty or The aerator has an irregular or reduced ACTION Remove the cover button (11). Loosen screw (10) with hex wrench (21). Remove the handle (9). Unscrew cap (8) (by hand only).
Codes/Standards Applicable: NSF/ANSI 372 UP C LEAD FREE IA C PM OR R NSF/ANSI 61 &T ASME A112.18.1 1.8GPM 6.8L/min maximum TM Faucet - Lifetime Limited Warranty Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com R If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
