R INSTALLATION MANUAL Urbix Industrial Bridge Kitchen Faucet TM KPF-3125 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List 1 2 6 7 5 4 1. 2. 3. 4. 5. 6. 7.
8 3/8" (213.04mm) 4" 4" 4" (102mm) (102mm) (102mm) 14 1/8" (359.98mm) 10 1/4" 11 3/8" (258.92mm) * - Adjustable height range. Installer Tip: Shut off main water supply before installing new faucet. 5 (313.4mm) 12 3/8"* (53mm) typ. (288.11mm) 5 1/2" (139.8mm) 2 1/8" (288mm) 9 3/4" (248.
NO Side Sprayer Option Step 1. Drill countertop Drill 3 holes into the countertop for the faucet body (1). Step 2. Install faucet assembly Install the faucet assembly through the holes in the countertop.
Step 3. Secure faucet assembly Secure the faucet body (1) with the rubber and metal washers (6) and the mounting nuts and screws (7). Do not overtighten. Make sure the plug (5) is installed tightly. Skip to Step 7. 1 6 7 5 Side Sprayer Option Step 4. Drill countertop and install side sprayer support Drill 4 holes into the countertop for the faucet body (1) and side sprayer (2). Install the side sprayer support.
Step 5. Install faucet assembly 1 Install the faucet assembly through the holes in the countertop. Remove plug (5) and install quick connector (4). Connect the sprayer hose (3). 4 3 3 Step 6. Secure faucet assembly Secure the faucet body (1) with the rubber and metal washers (6) and the mounting nuts and screws (7). Do not overtighten.
Step 7. Connect waterlines Connect waterlines to angle stops. Tighten with a wrench until snug. Turn on hot and cold angle stops and check for leaks. NOTE: Make sure filter washers are installed. Step 8. Flush waterway Remove the aerator from the spout. Turn faucet on and let the water run for 60 seconds to flush any debris.
Step 9. Adjusting spout height Unthread the holding nut (1) and pull the spout (2) up. Thread the holding nut (1). 2 1 1 NOTE: The adjustment can be up to 1". Lock to the desired location. It is recommended to set and forget, so the grease does not get worn. It is recommended to wipe the spout after setting the height.
Replacement Parts 8 Replacement Parts List Finish/Color Part # 1. Aerator Housing SFS, MB, BG* KP44031 2. Aerator 1.8 GPM RD* KP44029 3. Aerator Washer KP44028 4. Spout O-Ring KP44036 5. Spout Sleeve KP44037 6. Diverter Cap KP44038 7. Diverter KP44039 3 2 9 1 4 10 5 6 11 7 8. Handle Button SFS,MB,BG,RD* KP44032 9. Metal Handle SFS,MB,BG,RD* KP44118 10. Cartridge Cover 12 SFS, MB, BG* 11. Cartridge Hot KP44121-H 12. Cartridge Cold KP44121-C 13. Base O-Ring KP44035 14.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated. Remove button located at top of handle. Loosen set screw with a phillips screw driver. Remove handle and unscrew cartridge cover by hand. Tighten locking nut with an adjustable wrench.
Codes/Standards Applicable: NSF/ANSI 372 UP NSF/ANSI/CAN 61: Q ≤ 1 UP C C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R Faucet Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.